Viewing all customer Discussions for:

S385-28 28" Series 385 Channel Balance

I need replacement window channel balance for a Pacific Window vinyl window. I'm sending photos with dimensions. Thank you. Tom

Part # 2730k 28" Do you have replacements?

Hello, I am looking to order new window balances and want to make sure I select the right one. The numbers/letters I see on my old one are 2740, EH, B.S.I. Thanks, Tony

Jeld Wen has been no assistance in replacement of the part. Part Information stamped: 27Ds 32 Measurement 1/2 inch width, length 28inch Additional Information on the pictures

I believe I have found in your inventory, a replacement for the channel balance for my Alenco 3710 series window (series 385, 28",with the 15-004 shoe and 19-005 top), however the existing channel is stamped 2790, and the options listed go to 2770. Not sure if the sash weighs more than 39 lb, and i ... (cont.)

I am not sure if you received my post, I am looking at several lengths of the S-350 series units to replace older balances. Pleas let me know if these look correct and I will order some of the 24" and 28" to replace several window sets in my home. I will also update our HOA on the availability of ... (cont.)

i am missing both balances. the window make is alenco. window measures 22 1/2 by 57 5/8 (interior measurement). The visible glass measurement of sash is 26 5/8. It weights about 14 lbs. Another balance of a similar make window in the home is #2730. Not sure if that means anything as they are a diff ... (cont.)

Do you sell the plastic pulley part in the 2750 balancer which the spring attaches to? When my balancers break, it is usually the tab on the end of this plastic part that the spring rips away.Unfortunately, this part is not strong enough which has caused many of my balancers to fail. Do they make a ... (cont.)

Part is 1/2" wide and 28" long from a CWS window. The bottom sash is 34.5"wide and 30.5 tall and weighs 23 lbs.

1/2 inch wide 28 inches long non-tilt window channel balance.Marking on channel is 27 5 which channel balance do I need? Please see the pictures

Hello, I have matched everything to the 385-28 series however, my sash weight is 38 pounds. Would the 2765 be the correct option or is there a different balance with a higher weight threshold? Thank you, Denise

I need 2 - 26 inch, 2 - 32 inch, and 2 - 28 inch channel balance mechanisms. They are 1/2 inch hemmed edges (metal is fold back to create an edge). There are no visible stamped or inked marking on the broken devices. The top and bottom fittings are shown in the attached JPG file. These are for f ... (cont.)

hi im tryin to purchase this item S385-28 but i dont know what stamp option should i get.. the marking i see is the 27 4 caldwell em...thanks Jojo

I just acquired a house built in the late 90's, and have a window on the front of the house (single hung) with a pair of spring balances. The window is very difficult to open, and when I do get it open, the right balance sticks in the 'up' or open position. While they don't look broken, I'd like to ... (cont.)

I ordered two 28" series 385 channel balance and after putting them on the window frame and re-install the window one top sash guide broke and the other one is partially broken. During the installation the coil from one of the channel balance (the top hook) got detached and I can't put it back in ... (cont.)

Hello! I need to replace the channel balance hardware on a bedroom window. I have attached photos of the channel shaft (stamped 27 3 BSI OC) and both ends of the balance frame. The frame measures 1/2" wide and 28" long (metal edge-to-edge). I need to confirm which channel balance hardware is a co ... (cont.)

Hello, I was able to identify a 1/2" series 385 balance 28" lenght however my stamp says 2790 which is not on your list. Please advise on proper one to purchase?

Hello, Thank you for your help. I have a sliding window that cannot be open or bestir say cannot keep open. I am attaching pictures of the broken part (first 2 pictures) that my handyman believes is the problem: top sash guide. measurement: 11/2 inch long and 1/2 inch wide. Attached are also pi ... (cont.)

I need some parts for different sizes of Guillotine Windows. Parts I need... Code ~~~ Quantity ~~~ Description #347 ~~~ 1000 ~~~ Keller Anti Rattle #2730 ~~~ 120 ~~~ 28" 5/4" Square Balance Rod (Block and Tackle) Including the ends in the assembling (Pic Attached) #1530 ~~~ 120 ~~~ 16" 5/4" ... (cont.)

need to know if the number 2730 conforms with it being the window sash? it is 28inches long and 1/2 inch wide. need to make sure that it is the right sash before ordering. Thank you