Viewing all customer Discussions for:

S385-28 28" Series 385 Channel Balance

I am ready to purchase the recommended S385-28 - option 2740 for my windows. I will be ordering 10 of these. I have realized I also need the top sash guides but cannot find a match.

27 4 BSI NL

Dear Sir or Madam, please help me find the right replacement part for non-tilt window channel balance. My measurements are below. Pictures attached. Thank you very much! Metal Piece Length 28 inch Metal Piece Width 1/2 inch CHANNEL BALANCE SHOE, WINGED Middle Width 1/2 inch Length 1 3/32 ... (cont.)

In the attached pictures the spring is 14 inches, the metal channel is 28 inches x 5/8,x 1/2 Is it possible to buy the whole assembly? the metal piece is fine but we need the plastic ends on both sides, and the metal piece at the end of the pulley string string. is broken ( the side away from the ... (cont.)

Hello, My current window balances need replacing and have a 2740 stamp on them, but I see this is rated for 19-26lbs. I have weighed the window itself and it actually sits at 30lbs so I'm assuming I would actually need a 2750 or 2760 stamped balance. Also, the current balance is 28" long and w ... (cont.)

Hello, I am looking for (2) channel window balances for a bedroom window. The metal part of the channel length is 28 1/16" long. The channel depth is 5/8". The channel width is 9/16". The markings on it are 27 4 EU CMC 2 I am looking for both sides for the same window. Pictures a ... (cont.)

The length (metal only) is 28" by 1/2".

Do you guys sale the 2830 29"?

Hello, I have a 27-4 Ed Caldwell balance that I need to replace. From your website, I think I need the 385 in a 28

the attached are pictures of the counter balance that was in a 30 inch window. I need a pair of these and also a pair of balances for a 36 inch window, same style, that doesn't have the old balances in the windows, so I can't look at them. I need both sets of replacement balances. My guess is the ... (cont.)

Dear Swisco, I'm looking for a window channel balance. I could use 4 of them. The window company is called Pacific Window Corporation. Part # 27-4 IX CMC 11. I have attached some photos for your convenience. Sincerely, Dean

Hello I need to replace a Gapxo balance for 1 of my Windows Watched your tutorial and am sending measurements : 28" long - minus end caps # 2740 a Please let me know if there is anything else I need to send in order to complete this request. Thank you for your help! Jane

I have Alenco windows installed around 1984. The balance is stamped 2730. Does your product S371-28 work in the Alenco window. If so do I need the black top caps and no additional pieces? All the plastic pieces on the current windows have failed.

Need to replace window channel balance. It is 28 inches long (not including plastic ends). Has the following printed on it : 27 4 EX CMC

The only marking on it says "27 4 FX Caldwell. It is 28" long and 1/2" wide. Thanks for your help. James

Hello, my windows use a 2740 S385-28. They are extremely difficult to close down--I have to hang on them! I am going to switch to the same PN but 2730 (sash weighs 19lbs exactly). However, several of my window sashes seems to move at the top (side to side) enough that when I install the sash and ... (cont.)

We recently ordered and received replacement balances for our windows (2740s) and when ordering, we followed the prior part number which had 27-4 Caldwell stamped on the part. After we had received our order, and were replacing the balances, we identified another piece that had 27-3 Caldwell stamp ... (cont.)

Hello, my windows have the 2740 28" S350 window balance installed. Several windows have become too stiff to close down! I weighed the sash and found it to be 19lbs, which qualifies for either the 2730 or 2740. So I ordered the 2730 and 2740 to try them out. The best seems to be in between. So the qu ... (cont.)

My balance spring is about 28 inches long and the only markings on the balance spring is 2730 AMP GP

please let me know the replacement part. Do I need to weigh the window to know the spring option?