Viewing all customer Discussions for:

39-028E Ellipse Style Single Arm Operator, 9-1/2"

Hello, Thanks so much for helping me identify these parts. I have Truth window parts in these windows. I need new casement operators. They seem to be single arms with the arms being roughly 8.5" long and 12" long. I put a tape measure on them in the images. They don't have to match perfect, the ... (cont.)

We are needed to order comparable parts that will work in place of these. We do need right & left hand operators. We are trying to order some additional parts to keep on hand for future repairs. Contact Marlin to discuss.

The number under this Right arm crank is 40055. It is a Truth crank probably from 1987. I can remove the main mechanism, but the bottom arm is rusted out and broken. I'm not sure I can even remove it. What can I use as a replacement part? I would prefer white, but at this point, I don't care. Once ... (cont.)

Picture #1 Here is the damaged bit looking up, there is a marking on the link. there is no c clip to on the hypotenuse bar to attach it to the post to the bar on the sill. There is a marking available in the middle hypotenuse bar. Picture #2 Here is the identical part on the good window correctl ... (cont.)

Hello, I am going to need both a left and a right crank of the same measurements, and they are both Truth cranks. If you need more measurements, or better pictures, just let me know. Thanks, Ian

Hello, my window that I need to crank open has stopped working. Hoping replacing the crank mechanism verse new window. The arms at the bottom say "Wright" and 2006. The actual crank handle says "semco". It keeps slipping when trying to crank, I've tightened the screw on handle but doesn't work still ... (cont.)

I need to replace these cranks and arms

We need to replace our handles on 1984 wood casement milgard windows. Can you let us know what handles we need to purchase. Thanks Chris

I am looking to replace a bracket on a Windsor casement window that no longer closes (it works fine to open it). I am assuming that maybe the gears inside aren't working properly. I've included a picture of the bracket. Is this something you can help with? Thank you.

this is a wright brand arm for a crank that opens to the right. I need a replacement crank and arm

Help! I cannot find the window hardware for this. It's an old one, our condo was built in 1964. The one I bought will not work. I need it to screw into the wood, not on side of paneling.

This operator for a Truth casement window has the number 45035-RH. The casing is a one piece casting, with a single arm. I have been unable to find a replacement Ben

Gear is slipping Info from window label series 850 ansi/aama 101-93 mst 3050 mfr code Best Built BBI-1

Entire crank unit needs replacing. Two or tree turns before engaging and slips when trying to complete closure, so closing is not possible using only crank

Need correct size window operator - Wright - Casement Window

Hello, I am looking for three crank replacements for these casement windows The faulty cranks are from Norco and were installed in 2000. The image on the far right is one that has been recently replaced...but I do not know the manufacturer or part number.

The latch doesn't fully close. You can push it closed but it pops open again.The other window has to be pushed closed from the outside and since it's on the 2nd floor and separated from another window ( that opens) by a window that's fixed, so it's a bit dangerous trying to close it. We are movi ... (cont.)

The window currently won't close all the way. It will crank in with about a 1-2 in gap from the seal. When you turn the crank at that stopping point, nothing happens. The window opens just fine, but I would venture to say that we need a new one. Unsure what will be a best replacement. We just bought ... (cont.)

lock and crank handel and window rod if needed for new crank handle Need 2 sets what if any finishes available

I am looking to replace the cranks on a weathershield casement window. It has a left and a right side. The numbers I found on it were 3581R and 3581L.