Viewing all customer Discussions for:

39-028E Ellipse Style Single Arm Operator, 9-1/2"

Hello, We need help deciding on which parts to get to replace the the entire crank mechanism (hinge arms, track, operator) on our 1980's Hurd double casement windows (left and right). Could someone help with this? Double casement widow width each 17.5" Hurd windows House built in 1982-4 Thank yo ... (cont.)

Act like the gear is stripped. Both sides acting the same

Can you help us find the correct replacement? What else would you need to know?

Hi, I would like to replace as much of the operational and trim hardware as possible. Color -White if possible. Fold down handle if possible. What would your opinion be as to what to use? Thanks so much, Trudy

I need a new Hurd window crank. It does not crank out or back in. The handle just circles with no connection to the window as it just swings out after unlocked. We have to push it back from the outside to close it. What part do I need? Thank you!

Have four windows with this. None work- each for a different reason. Some just open, some just close, but not do both. No markings or labels other than symbol on hand crank end.

Please help to identify

printed on the bottom are the numbers 05312004 2341. under these sequence of numbers stamped in the metal there is the number 4 by itself, and then the numbers 45251. I was having a hard time locating this exact part and I am also unsure of the color. please let me know what you think Thanks, Brian ... (cont.)

Wright is the label on it. Small crank knob. Opens from left to right so mechanism is on the inside right. Photos are of the window on the left, not the broken on. My name is Michael

The clank will open the window, but it starts slipping when you try closing the window.

See identifying numbers in photos attached

I believe this is a Nine inch Arm 9 ( Center of Povot to center of Crank is 9/12 in) Not sure two names listed "Weather shield handle" and "Truth" on crank arm /casting

We ordered 39-028 & 39-014 to try on our windows. Everything worked except 39-028, with a 9-1/2" arm, was too short and 39-014, with a 13-1/2" arm, was too long. We really need a 11-1/2" arm but can't seem to find that. Do you have any suggestions? Thanks for your help.

The name and number stamped on the assembly is Truth 30382. I really need the right side, but if the interior hardware is different than the picture I should probably replace both the crank and interior cover. If you can, please identify replacement parts. Thanks for your help.

Help... my name is Mark, i had a broken crank style window handle needs to replace.Before i place the order. These are the information i have from the existing window ( MI Window & Doors ) 12862423.6 9700 . Does ELLIPSE STYLE SINGLE ARM OPERATOR, 9-1/2" Product Code: 39-028E a good replacement part ... (cont.)

Can I replace the bearing wheel instead of the entire single arm operator assembly? If so, questions: Is the pin threaded? What exactly would the replacement part be called? Do you stock these parts?

I need to replace the crank/operator. Can you help me figure out the parts I need? The window crank unscrews and can open but not shut the window anymore.

Please advise if you have these exact systems for replacement. Long arm is 9 1/2 ". Crank base is 4" wide and 1.5 " deep. Need it for left opening window as well as right opening window. ( Pict.# 2916, 2917 ). Part # 20810 The 3rd window are pict. #2918, 2919, 2920. (9 1/2" long arm. Base5") ... (cont.)

Window crank broke on Sun Casement window. Will crank out but not back in. Probably need the whole crank assembly. Window was made in 1987.

Do you supply the operator in the attached photo if so I need 15 right and 15 left 9.5 inches? Regards, Kevin