Viewing all customer Discussions for:

81-266 1-1/4" dia Roller And Axle Kit

Hi- the wheel broke to our sliding glass door. House was built 1968 in Hollywood,FL not sure when doors were updated

Hello, I'm looking for 2 new rollers for this old patio door it's very heavy.

This is for a five foot sliding door.

Hello; I have 4 sliding patio doors that have rotted nylon rollers on them. Do you have the rollers in metal instead of the nylon? Living in the desert southwest plastic doesn't last here. The wheels are about 1" in dia. 1/4 wide with a groove in the middle, 4 doors X 4 wheels = 16 wheels. I ju ... (cont.)

Hello,Based on your dimensions, our 23-043 seems like a good match but make sure to compare the dimensions on our product page to yours to confirm. Though it's not a requirement, if you want to stick with steel wheels you can purchase the 82-226 81-266 roller and axel kit to switch out the nylon whe ... (cont.)

I can not find a similar roller.

The patio door was installed in 1957. i need to replace the roller and am not sure of the part. I dont think it is still being manufactured, but need to know an equivalent part?? thank you

Hi, trying to find rollers for a sliding door that was installed 40 years ago from Australia. No branding that we can find- the wheel is 1-1/4" diameter, width of the whole bracket is about 5/8" (16mm). One side has an F tab and the other side has a clearance hole for a screw to attach into the alum ... (cont.)

Hi Swisco, I am looking for a replacement patio door roller for a Peachtree door See attached photos

this is what i pulled from my 1968 sliding glass door,i have not came anywhere close to replacement parts,as u can see one of the adjusting parts broken ,the roller wheels fit right into bottom rail,is there any universal roller assembly i can use,please help

I have two sliding glass patio doors with roller assemblies that need to be replaced, but i have been unable to locate any information on them or the door. The doors might be custom made replacements for the originals.The roller assemblies are fit into an aluminum extrusion inside the door frame, ra ... (cont.)

Our patio door has a single long assembly that fits up into the bottom of the door. There is a single wheel as shown in the photo near each end. The wheels are marked Kilian and Syracuse, NY. They are 1-1/4" OD and 1/4" wide. They have a 1/4" ID center hole. They are nylon and have a flat outer ... (cont.)

what is the id for pin

I think it is close to the 81-286, however the dimensions of the 81-286 are not the same as the part I have. I have looked through all the single wheel patio rollers and do not find any others that are like this. Am I missing anything? What are your suggestions?? Is there any way that I could just ... (cont.)

Should an axle that fits in a roller be snug or loose?

I have this identical door and need two roller assemblies. I have the same metal plate on top of the existing rollers, that I can remove and place on a new roller. Not sure the 81-018 will work though, because the wheel bottoms when raised all the way up, MUST be even with the bottom of the tabs. Pe ... (cont.)

This is all the info I have. I asked them to send me sizes but they can not at this time. I was hoping I can get it Identified before I head 2 hours away

I need two of these rollers for an older sliding patio door. I have looked through the items you stock and I could not find one. I do not know the maker of the doors. I hope you can recognize it or have one that would work. I have attached a picture.The measurements are 1 1/2" long (not including sc ... (cont.)

No markers just the pics if you need more please let me know.also if you can determine the make of door i nee the door handle and lock system the house was built 1976 i purchsde the home in 2010

Pat 3670357