Discussions for 33-016P : SWISCO.com

What size Screws do I use with the 38-075?

Hello, What screws do I need for these Sash Locks in White? Thanks.

Looking to replace cam lock

I need a replacement casement window latch for an older Caradco window of late 70s to mid 80s. Window is hinge on left and a latch on the right.

+1

Hardware replacement

I need 2 different operators, I think dyad and dual. Also the latches 2 different kinds , stud brackets and hinges(10" and 14").

+5

8 swing window hardware identify help

Hi,I need help with replacing the hardware on these older windows I believe from the 80's.There are 8 total but I am sending pictures of these 4. I drew the dimensions on the pictures.I can customize as much as you recomend so don't worry if yhere needs to be modifications to the wood. ... (cont.)

+1

Awning window

Norco pre 1992 awning window left hand

Constant force window balance

Hi i would like to order 2 constant force window balance for the left and right side of the plastic window The weight of the window is 12.1 kg I need shoes and coils springs as well I suppose. Do i need to change anything else? The window has 2 brackets on each side which makes it difficult to ta ... (cont.)

+8

window parts

this is the whole part and also just the back piece - we need some of the whole part and some of just the back.

Casement Window Sash Keeper Needed

The painters lost our window sash keepers that were mounted on the casement window. Do you have a keeper that will work with this Casement Sash lock? Thank you.Perry

+1

Andersen window parts

I'm looking for a window crank and operator cover for an Andersen window. This house was built in 1974. Thank you

need help replacing these parts

(18) S795-17 : 17" Series 795 Channel Balance (18) 26-200 : Balance Screw Plug (18) 33-016P : #8 x 1" Phil Flat SS Screw is should have been 27" also need bottom pins to fit 18 each and 6 air latch img 3219

Window latch

This is a latch for an old window that opens out. If you can help me with this latch, I need one for a left open window and one for a right open window. Thank you very much.

Entrygard Dyad Operator

Is there any way to adjust the operator? When you purchase a replacement. Is the handing designated from the inside or the outside of the window? Thank you

Searching for 14D304

Looking to replace some of this hardware. WeatherShield approximately 2003

+2

Locking handle

I ordered something like this from your website but the locking lever was to short only 2 inches didn't lock. The original locking lever is 21/4 inches . I also need the screws 38-126 hopper window lock was what I ordered from your website Order number 1517678

Pozzi casement latch trim screw, bronze

These windows were installed in 2003 and after painting, many of the trim screws have gone missing. As shown in the photos, they appear to be #8 x 1", flat head phillips, 18 threads per inch, with the head painted bronze to match the trim. Any ideas where I could get some matching screws? ... (cont.)

Questions about secondary door locks

Does the 33-016P screw fit the SECONDARY PATIO DOOR LOCK, WINGED and SECONDARY PATIO DOOR LOCK, WINGLESS? What is the bolt's diameter of the 82-040?Can the 82-051 be mounted to the track that's in front of the sliding door (the bolt would go into holes already drilled into the bottom of the slider f ... (cont.)

Entry Gard Sash Lock and Keepers for Casent Window

Hi, I'm pretty sure these are entry guard sash locks because the casement windows hardware is Entry Gard and they look very similar to your 38-097 product but mine are not quite as wide as that model. my width is more like approximately 2in wide. is there a part for me? I also need keepers for LH ... (cont.)