Viewing all customer Discussions for:

26-244 Tilt Window Latch, Right Hand

Needs to be double slotted and original was scallop nosed. Brixwell seemed to have something similar but only shows whole latch. Need to order your 26-234 for another window and would like to consolidate all in one order.

I have a lot of Farley tilt vinyl windows and need a lot of the top tilt latches. the closest one I see on your website is #26-390 but mine measure in length at 2-3/4" long and 3/4" wide and 7/16" total thickness. It looks very much like the 26-390 but the 2-7/8 will be too long. Maybe the 26-243 wo ... (cont.)

Hello! These are the parts I need. So, I need you to give me the number of these pieces so that I don't buy the wrong one. I will need 10 white pieces from each unit, with the exception of the piece in Photo 5 (4 pieces + screws). These are the numbers I can see: Photo 1: I 11079 PAT. 4824154. On ... (cont.)

window tilt latch looks just like your part # 26-244 or 26-243 but is smaller (shorter). I am attaching pictures. We have many houses in our Resort that were built around the same time by the same builder so may be a popular item here. Can you help?

I could not find identifying numbers for these windows that have broken parts. The window weighs about 15 lbs. I do not know if the replacement spring balance value for each side should be 16 lbs as listed in your web site or half that value. Also, I do not know which of the many pivot shoes is the ... (cont.)

One of our window is falling out due to broken plastic piece.

These windows were mfg in 2007. Need to replace several tilt latches, both sides on many windows.

I need four tilt latch replacements the windows are not at my location

Looking for parts show above. The window was installed 2009

These springs are 1/2" wide and I also need new covers. What parts do I need and is their an install video or info?

Double hung window36X48 r.o.Also need two thumb tilt latches left and rightTwo constant coil balances one left one right

Hello, my pictures are of the LEFT tilt window latch. Both left & right latches are located in the upper corners of the lower window. Im looking to purchase 2 sets (left & right) of these items. The pencil picture points to the area that slides into the window.

Pictures 1 & 2 These latches slide into the frame to lock the tilt window. I don't see the same item in your online catalog. Do you have this latch? Picture 3 and 4 are a snap in liner that snaps into the window frame above the latches to keep the channel centered and to provide a backstop for t ... (cont.)

These are the left and right sides of the tops of the double hung windows. They keep the window attached to the sill, allowing it to slide up and down, but retract when tilting the window in for cleaning. Please help with the identification so I may order 4 of each piece. Thanks! ... (cont.)

Hello,Your assistance identifying my window parts would be greatly appreciated. I have attached photos. I labeled the photos with what I'm looking for since I don't have the proper nomenclature.I would like to identify 5 different parts, and will be ordering multiples of each as I own several rent ... (cont.)

Hi, hope my pictures will show what you need to identify replacement window latches. I assume they are sold in pairs? Than you very much You have helped me before. Love you guys!

I am looking for the window spring loaded tilt latches both left and right sides. All the latches are broke and the windows do not stay closed. Model 4000 Bat 9717809-18 WO 174484-1-A1-WO1 Please let me know if you can help me. Thank you Judy

Good morning, I am looking for this till window latch, both left and right. I hope the photos are adequate. Please let me know if you require any other information.

I recently purchased 26-420 and 26-419 tilt latches for my windows. Everything size wise fits except for the clip that holds it in the window. It is shown as 3/8" in the attached picture. Do you have this same latch but with the clip at 1/8" or 3/16"? Thank you!

I have been trying to find a tilt latch similar to this, but the ones I have found are slightly off and I have to use a Dremel tool to shave off the excess plastic that would prevent it from fitting, But they are still a tight fit. I have several windows like this in my house and my neighbors have a ... (cont.)