Viewing all customer Discussions for:

15-001 Channel Balance Shoe, 1-1/8" Depth

They are 27 in long. Looking for replacement

The plastic parts of the channel have broken and it is only assisting from one side.I believe the channel I'm looking for is the series 370. Mine is 35" long and the lower shoe looks the same but my top guide does not have the "wings" protruding from the sides as your image shows. They don't appear ... (cont.)

Length 27" . Please see photos width is 1/2"

Thanks for your prompt response Attached please find new pictures as requested. Magazine , should you need any further information , please let me know ASAP as I need them urgently Hope this will clarify the reference needed do I can place the order Waiting for your instructions

Hello, Here are the pictures. 1. I need to replace the balance track. 20" tall, and the header and foot as shown. The balance shows 2140.I know we have integral with header and foot, please tell me the part number separately. (balance, header, shoe in case in the future use) 2. I need to buy some ... (cont.)

I think the tops I can identify. But the bottom don?t seem to be pictured on you site

I am looking for a replacement channel balance. Mine is labeled 28.5 LQ Caldwell. It is 1/2 inch. Can you please direct me to the appropriate part? These are in a CWS window.

I have channel balances in my windows. But I can't find these exact tops and shoes on your website. Do you have these parts?

Need replacement balance 24" options stamp 2420

The only number stamped on it is 2730. It's 28" tall, 9/16"wide, and 5/8"deep. Wings on top are 15/16", top is 1 1/4" tall Bottom shoe is 1 1/16" deep, 1" tall, with no wings

I am looking for a 31 1/2 Caldwell balancer

Replacement part for window, left side slide mechanism broke.

Good afternoon, I would like to order 2720 channel balances. I am not sure which ones to order I have included pictures..

Please help identify and by two of these. I know they are 1/2 inch wide and 28 inches long. But the ends did not match any on your web site.

I need to replace broken Block and Tackle Window Balances. Do not know who is the window manufacturer. It is a non-tilt window and side load. Measurement is 15" and a 9/16" channel. The window has a label w Mfg Code YOM-1 Series 9500. Window H-R50 53x74 The marking on the broken one is 14 ... (cont.)

I have old viking windows and need to replace the balance on many of them. On the window frame I found the label: Viking industries Spec: DH-B1-HP (45) Series: 80/85 MST: 4066 On one of the balances I saw 2830 marked. On another 2280. Is there a difference between 2830 and 2280? It is a h ... (cont.)

Window slider spring for raising and lowering window. I do not have any identifying part numbers. Window slider spring goes on inside channel of window. Measures:1/2" x 1/2" x22" in length.

I have several windows with broken sash parts. When looking at the windows Channel balance look too long. The balance top part appears to be 19-002. The bottom 15-001. The rail is marked 2140 and is 22" long. The window is 22-3/4 high so I think the channel balance is too long. The window weig ... (cont.)

I have a 2740 channel balance. The shoe appears to be a 15-001 but I didn't see anything like the top. I found a similar one on this site labeled 19-037, however mine is only 1 1/16" at its widest point (the "wings"). The channels on my windows are only about 1 1/8" wide.

I am trying to replace the balances on two windows. They have some faint markings that say "24-3 68(?) Caldwell". They are 5/8" deep and just slightly more than 5/8" channel width (11/16"?).