Viewing all customer Discussions for:

33-109B 10-32 x 2" Bolt

Please let me know if you carry same lock

Hi, I'm looking for the replacement parts of the glass door lock (see attached photos). Please let me know if you have the parts available. Thank you.

Looking for this handle which I think I found on site and the screws that go in not sure if that's the standard Anderson bolts mine snapped off inside

I broke the handle off the Anderson sliding door which operates the lock/latch. We didn't remove it because it's a main exit and if we can't put it back our house wouldn't be safe. We are using a screw driver to lock and unlock itThank you!Carol

Hi I have a PPG Herculite K Sliding Patio Door. My lock is broken, and it doesn't work. I need to replace the broken lock but has been finding it difficult to get the right parts from Lowes, Menards and Home Depot. Here is the information located on the corner of the glass door: PPG Herculite K ... (cont.)

Hi I need set of lock and handles and thumb latch. Can you pls provide the quote. Thank you and regards Zafar

Hello, I need to replace these two with stone color interior handle and lock, also with bolts, thank you.

I have a sliding door interior handle for which the bolts have loosened and become disengaged. When I try to reinsert and tighten the bolts are not reaching. The bolts have their thread. Candidly I am mystified as to why this is happening and I don't want to order replacement bolts if they are no ... (cont.)

Here is the part number: Bolt - Handle Package: Stone: 1275210 For Andersen sliding glass door Need bolts for handles

How long is this bolt? My door thickness is 1-3/4". I want to order the replacement handles and bolts if they are long enough.

I have patio door installed in about 2000 +/-. I need an interior & exterior handles because bolt is stripped. Can I just order bolts or do I need new handles. If new, would these parts work: 88-013, 88-014, 33-109B? Thanks!

Cap end snapped.

White ,on the inside of the handle it says Andersen Corp bayport minn.screw holes look like 5 1/2 on center

I purchased part # 33-109B two pieces but they are too short for my handle, I need them to be an additional 1/4" these are two inches. My order # was 1273565. I think I may have been looking at the wrong handle mine does not have a backing piece.

Door was installes prior to 97 thetefore no serial #. I am looking to find a replacement handle as the screw hole for the exterior is stripped. Holes are 6.75 inches on center apart.

I need to replace my door handle with a crappy improvised installation and swiss-cheese holes cut in the door frame. The door is an unusual 2" thick. The handle appears to have 4" between screw holes, which I assume is actually 3 15/16". The lock is centered. The door is rather heavy, so the str ... (cont.)

1998 Andersen sliding patio door. Need replacement exterior handle and screws. I see the interior handle on your site but not the exterior part. Please advise.

We ordered part #88-013 and 88-014 from you but the handle is to wide on the side where it meets the lock or door frame. See the pic for the screw holes and how little space there is. Can you help find the correct one? The screw holes are perfect.

I don't know what to call what seems to be the defective part of the assembly but that is what seems to be the problem. For the sake of discussion I will call it a "nut" (circled in picture) The problem is that the screw won't bit fully and screw into the nut. So, the whole handle doesn't attach fir ... (cont.)

I've looked all over for replacement handle to no avail. Top part of Handle split vertical (duct tape covering in photo so handle is useable to get outside). Center-to-center hole of screws is 5 5/8" and 6" from bottom of bottom screw to top of top screw. Total height is 7 1/2" I have no idea whom o ... (cont.)