Viewing all customer Discussions for:

33-071 #6 x 3/8 SS Pan Head Screw

Need balances that measure 18 and 21 inches in length. Also any additional hardware required. Thanks Craig

Looking for the correct replacement part.

I have one of your shower doors, and they vinyl sweep is no longer good. I'm trying very hard to replace it, but I can't seem to find one shaped like the one I'm replacing. Any help would be greatly appreciated! David

This is a framed glass door. Sweep and drip rail have separated from door. Cannot find screws for the attachment. Need suggestions to remove and re-install. See pictures IMG_1067.jpg IMG_1066.jpg

Hi I 1ea chrome and 1ea bronze both 24?. They look like your 10-324

Hello, I need a replacement 3/4" X 24" shower door sweep seal. I have attached pictures of both the extruded aluminum channel and the seal itself to give you an idea of what we are looking for. Unfortunately, I have not been able to locate the seal anywhere. Thanks

We just bought a house and have no info on the windows installed. After reading some threads and looking at pictures, I think that the right replacement part that I need is the 15-177 Coil Balance shoe. 1) Do I need to replace the coil as well at the same time and if so, how do I know what series ... (cont.)

I didn't see a photo of the coil balance for my bathroom window. The coil balance measures 1/2" wide by 1 3/16" diameter. It has a letter E stamped into it. The sash weighs around 10 lbs on a bathroom scale. Printing on the sash reads: Rehau K 600287-001 10/31/04 13:18 9882 The window is a ... (cont.)

I have a rental home with two windows that won't stay open when opening. The city inspector said I need to repair or replace these windows to comply with the building codes. Only the bottom sash needs to be repaired. The first sash is 16.5" H X 31.5" W. I do not know how much it weighs. The s ... (cont.)

There are no markings anywhere in shower to identify it. It's original probably mid 90s. I'm looking for a replacement for this drain rail. I don't think it ever had a plastic or rubber sweep.

Hi, I have what looks like a "home made" shower door and need to find a way to prevent water from leaking over the threshold. Is you door sweep the right solution for my needs?

I have a 1989 door and the rubber strip is falling apart. I can't find the strip so I assume I need to replace the whole sweep. I can't find anything like I have that wraps around the door. What do you suggest?

It looks like there are predrilled holes on the aluminum drip rail to screw into the framed door. How many are there and how far apart are they? Also, my shower door is 33 1/3 inches. Can this drip rail be sawed?

Hi - I need to replace a shower door sweep that slides into the bottom of a hinged shower door. It is a T top - the top of the T measures 1/4 inch across. It is 36 inched wide and 1 inch deep. Can you please help? Thanks

When securing the 10-324 shower sweep with rail to a metal shower door frame with the 33-071 screws, what drill bit and size should I use?

this shower is 29 years old .....the door across the bottom is 30 1/4 ' the part is 30" the holes ar on either side and in the middle.

I like this design, but need a longer sweep, please. This appears to have only 23/32" below the bottom of the shower door. Is there a model with 1" of actual sweep? thanks.

Do you sell a set like the pictures? I would like to order enough for 10-20 windows. Sash weight is 18. 6

shower door frame is 27 1/4" wide, 3/8" thick bottom edge, metal strip is 26 1/4". This is a over 20 year old shower door. Rubber and hardware rotted and deteriorated due to very hard water. Attaching screws rusted out.

Need parts for new construction vinyl window. Purchase around 2001.