Viewing all customer Discussions for:

39-025 Awning Window Crank Operator

I am usually very good at sourcing, but I made a huge mistake selecting the company to replace my broken window crank. I should have known when they insisted my photos and description wouldn't be enough to go on and told me I had to mail it in. I was very reluctant ,since it was the only one, but pr ... (cont.)

There are no markings on the part or window. Could you idenify the part with just photos. Thanks

I spoke with one of your representatives and he thought I had a 39-025. However, when looking on line at that operator, the link inside has a slight crook in it, where as you can see from the pictures below (the 4th picture) ours is straight and is approximately 2 3/8". I just spoke with Tim a ... (cont.)

I have purchased the 39-025 window crank operator in the past but do I have to purchase the entire crank . The problem I am having is the crank handle seems to be stripped it turns but will not close the window it will only open the window

Can you replace this crank operator 39-025 with one that is flush or folds. It gets in the way of the blinds. I know I can install blinds outside the window frame, but would like to install inside the window frame. Thank you, Caron

We have found a product that is almost the same as the peice we are looking for there are just a few differences. The part I need is 5 1/4 inchs long from top to bottom bolt.. there are two bolt holes on the bottom that are 1 1/8 from center of bolt to.center of bolt..the extension arm is 2 3/8 inch ... (cont.)

What is included with the 39-025? I particularly need to know if the shoulder hardware is included (shoulder screw, washer). Thanks

I have an operator with the same mounting hole locations and construction (shoulder bolt washer, #10-24 thread bushing)as the 39-025 except the link is 2-1/2" instead or 2-1/4" long. I think it is from a Peerless aluminum awning window. Will this operator work with this window despite the 1/4" lin ... (cont.)

I have a jalousy window which can be opened but can not be closed because when I try to close it the handle just comes unscrewed. The window doesn't have any markings on it - model, brands, etc. I can push the window closed from outside (i.e. it's not stuck), but it still leaves a gap.. I need the ... (cont.)

I am sending a pic of the windows and the crank. I cannot find a part number. Can you tell me where it might be located?

I need a replacement for this awning operator. Please let me know the part number. i cannot find any marking or number in the hardware. Thanks

I am not sure what model or manufacturer I have. The B dimension is: 1 1/8” The C dimension is: 2 5/16” or 2 3/8 And the thread on the end of the connecting rod is 10-24 MECHO EN EL SALVADOR CA

I have 10 awning windows with this operator and the handles are beginning to break out of most of them. Looking to replace them all. There are no identification marks on them other than a "1" molded into the underside of the handles. The room was built in 1983 and the operators appear to be or ... (cont.)

Hello, I am looking to replace several jalousie window cranks/assembly systems on my porch windows. I have a attached several photographs in an effort to determine what I need. The unit measure 5 7/8" in length. Thank you Eric

The existing part has K D J AL markings on it aproximate 5 inch hole to hole on housing about 2 1/4 inch on arm link. I can send photos if you supply email address and persons name I should send them to. I need 4 units along with screws and crank arms . Right hand

ok I feel a little foolish. I may not have ordered the correct part. the long length( bolt holes) is correct at 5 1/4", the two bolt holes at bottom are 1 1/8th a part, but the arm is 2 1/2 long center of pin to center of threaded hole. If you have the correct one it would be great. I did not know ... (cont.)

I just moved into a new house and half of the windows in our sunroom (which are now stuck in the open position) need replacement cranks, but I have not seen any like these anywhere. Can you identify them and let me know what kind of replacement to order? Thanks! -Kate

I need to replace a window crank with the following specs: Horizontal spacing - 1 1/8" Vertical spacing - 5 1/4" (top hole is offset to the inside) Arm - 2 5/16" #76 (stamped on arm) Arm Hole - 3/8" Stamped inside housing is a large 93 and PAT NO D-198202 US 12 RD 1963 CAN R H Not sure ... (cont.)

Please provide help in identifying part shown in photos. Sincerely David

We need to replace an operator and are not sure what the arm is and what to measure. We did not find a name on the operator. Can you please help. Thank you!