Viewing all customer Discussions for:

Door & Window

Hello,I need to replace the balancers on 4 windows. Please advise if you can help me with this..Thank you!Robin

I'm looking for the bottom pivot for this casement window. Pivot and track. The picture of the operator is the only markings on the window.

I can not find this specific pivot bar can you lead me in the right direction or recommend an alternate. Please and Thank you.

This is the palmair breezeway jalousie window operator. I need 1 left handed. Thank you.

I need the following for a casement window. (2) Hinge Arms Left Top (2) Hinge Arms Left Bottom (2) Hinge Arms Right Top (2) Hinge Arms Right Bottom Thank you,

Looking for some replacement top sash guides. Just looking for some that will fit my windows.. balance is a 17 inch, 1620. I will include some pictures..

I'm looking for all the operating parts for a pella casement window. I need top and bottom pivot slides, the locking armature, top arm, plastic slides, all parts. I have two windows that have been screwed shut and all parts removed due to rust and age and the owner wants to rebuild them so they op ... (cont.)

Can't identify 17 year old vinyl double hung windows. Need to replace the balances for upper and lower sashes! Only marking on the balances are the ones in the pictures, 22 hd for outside and 23 hd for inside!

No hardwareAnderson French doors Inward in swingSUBSTITUTE FOR ANDERSON

Hello, Can the Truth Hardware low profile sash lock be used in place of the Primary casement sash lock? Also, what is the function of the handleless secondary casement sash lock? How does it work? Thank you!

These cartridges are from the same window. Both need replacement. One reads: 827 2 75 the other: 827 2 K75 93. Is replacement cartridge 37-837 correct?

I have several Gentek Double Hung Windows (Installed in 2014) where the pivot shoe is broken. Can you please help me identify the right pivot shoe for these windows? I have attached a picture of the original pivot shoe with dimensions. It is 0.5" thick with a height of 1.25" and a middle section wid ... (cont.)

The above pictured Truth mechanism on my Marvin Bay window (left looking out from inside) casement has stopped working. I believe the Marvin serial number is 01 1G 00 OBA IGMAC, however, I'm not sure if the 00 are CC because it's really hard to see.

I have a customer whose rollers on his Guardian sliding glass door need to be replaced. They gave me this information from the door. Z971-1984 SGCC9331/8U 16CFR120111 CGSB12-GP-1 Can you help me find the replacement rollers for this Guardian sliding glass door? I've uploaded a picture of the ... (cont.)

Bottom fitting measures 1 1/8 inches. Length of the metal is 21 inches.

I need to replace hand cranks in 4 windows in my biome that was built in 1987. Two of the window cranks have the following numbers on. 20810 along with R30842 The two other windows that is part of a three window larger unit has only the numbers 20544 on them. This would need to be a right and left ... (cont.)

A piece of this trim is missing from my window. Window Manufacturer is CertainTeed they claim they dont have or make it. I am looking for a section that is 5.5ft - 6Ft that I can cut to fit.

Pivot shoe = 5704,165 3 Coil springs = 44.0 35" T52322 (questionable on this-hard to read) Coil support is in pieces - deteriorated by the sun Don't know about the pivot bar The plastic has failed on the coil spring cover, making the windows difficult to open and close, however the coils look fairl ... (cont.)

Need 3 brown covers and 3 mechanisms

Hello again! Was wondering if I couldn't get your assistance procuring some balance rods. The only markings are the numbers stamped 2950. The weight of the window is 27lbs. Photos attached. Thanks!