Viewing all customer Discussions for:

Door & Window

I have a window with a 27 b and the otherside is 27 d see pics for rivet placement Gut says get two inbetween What stamp should i order?

Looked at your selection, could not figure out which one was the right one. One is an upper the other lower that amps in. Any help would be appreciated

My window will no longer stay up and I had the attached part fall out of both sides of my window. It has a small rope/pully system that the rope is broken in. There are no markings on the piece to tell what part I need. The only engraving I see says "25 9"

Hi. I need a four of the nylon sash cam for my windows. My block and tackle measure 25.5" metal end to metal end. The cam sash's measure 5/8" width on both top and bottom. No "wings"...they are not wider at the top than at the bottom. I measure a width of 5/8ths, a depth of 9/16ths and the height co ... (cont.)

Greetings, I am contacting you today because we are in need of 6 vinyl handles four our vinyl double-hung Thermal-Guard brand Windows as they have been breaking over time. These handles are 2.75 Inches from side to side and attach to the windows from the bottom with a single Philips screw (pic ... (cont.)

This is a (1936) wood double hung window. The coil is 3/8" and the channel in the sash appears to be 1/2". Would a series 400 spiral balance work? (The description says for aluminum windows). With a #32 bracket? And could you please tell me how to measure the length for the replacement. Do I ne ... (cont.)

do you have these? no identification markings

Need about 26 pieces 6? long. Dimensions are about 5/8 x 3/4, white vinyl.

Need to replace this coil balancer. (Do we ever replace with spiral balances?) Window is a double hung, American Craftsman. Coil holder reads 9.0 lbs I don't find a T ended coil in your catalog. Need all parts, 2 sets. Thank You

Need replacement for Norco window crank 40471 #30470LH on long arm and measures 9.5? has Entry Gard truth stamped in it S shaped #3084L measures 4? Base of crank has Truth stamped into it

Hello. I am missing the piece shown in the picture to a sliding door (picture is from another sliding door in the home). The other picture is the sticker on the door.

this is the only picture I have, I hope it helpsI need 2 balances & 1 stud is broken on windowthank you JACK

7 3/16 longFirst hole from top is 1 9/16 to center of holeCenter hole is 3 5/8 to center of hole going from topThird hole is 5 9/16 to center of hole going from the topThickness of door is 1 1/16made by sash controls inc.

I think I need https://www.swisco.com/26-inch/pd/Series-385-Channel-Balances/S385-26 Stamp says 26 4 BSI RN Any help would be appreciated.

Hi - I have tilt out double hung K&K brand windows, and bottom window won?t stay up when opened. I took it apart and see the cam pivots (black ones in photos) are broken. Will your ?balance knife lock shoe 15-014? work for the K&K window balance? The balance in the jambliner is ridge lined and stam ... (cont.)

I am hoping you can match this roller for me.

Hi there, I am trying to fix a new construction window. I weighed the window and it was 40lbs. I'm looking at the broken balance and it's stamped 32C. Was this balance the wrong one? I remember when we moved in and had the windows (Plygem) installed, they were installing the balances somewhat haphaz ... (cont.)

Looks like coil has snapped. No ID number on the part.

Looking for 3 sets of these window parts. Do you carry them?Thank youBarry

Hello. A big wind storm blew our window out couple months ago. It appears that the hinges on top and inside the frame are gone. The photo with the two little metal pieces and pieces of plastic was all that was on the floor after the windstorm. Are these parts replaceable? And if so how much will the ... (cont.)