Viewing all customer Discussions for:

Door & Window

We need to replace this latch for a sliding glass door, a Fleetwood SGD 30 series 10001 round face.

I am trying to find replacement single hung balancers for Older Viking aluminum windows.

Hello! Hoping you can help. Opened my Pozzi crank window this morning and whatever attaches the crank mechanism to the window popped off and now I can't close my window. I've attached pics. Is there a screw or a part that I need to get the window to close again. Do you have what I need? Look ... (cont.)

I would like to put a keyed lick cylinder on the outside of my bf rich door. It is a 1000 series door, part # bfr-m-17-00042-00001. The door is made to be adapted with a lock cylinder, but I don't where to find them

Hello I am looking for 3 round 4" Nicole hinges (Penrod brand)

what is the difference between 15-004 and 15-005 bottom guides? Mine is one of them.

need balance clip. We need the grey part. It slides into the white part I also uploaded. one end goes to the window (sash?) other end goes into the white circle part I also uploaded.

Looking for replacement latch for patio door made by Air-Lite Lanaidor Metal Ptoducts in Oakland CA. Standard patio latch does not fit.

I had triple-track storm windows installed 25+ years ago. The word "DACO" is embossed on the spring loaded latch. On two of my windows I managed to break the top corners that fit into the track when the window is installed. What is the best way to determine which part will be a suitable replacement. ... (cont.)

Need help if you can finding this part. DORWAL

Is this enough information for you to match these awing window operators. We need 8 operators and handles. Tks

Last week I did order 28'' series 385 channel balances from Swisco. I received them yesterday and they are 1 inch smaller and the shoe is different than the one I had. I ordered 28" 385 series because the sales person at Lowe's told me this was the one I needed (according to the number on my old b ... (cont.)

I am looking for glazing bead for my double pane Better Bilt windows that I am assuming are original to the house (house built in 1994). The glazing has either separated from the window, waved or is missing in some cases. The glazing has a curved side that snaps in between the window and frame. The ... (cont.)

I have a house built in 1978 with channel balances. The take out clips are plastic not metal. Due to age, the plastic became fragile and breaks when I tried to pull them out. Do you know where I can get replacement take out clips that will fit. Dave

Hello, I just need to find the proper replacement. Can you please identify this balancer? The only marking is 28B. Thanks, Fernando

I'm looking for rigid vinyl glazing that is a 1/2" wide by 1/4" deep channel that is paintable. This is for windows made by Sunlite(TM)which were made in 2001. I don't believe that they are still in business but the window are functioning fine except that the glazing is warping and I'd like to repla ... (cont.)

Need to know if the 95-262 and 95-263 are available in tan? We will be ordering both white and tan in large quantities.

I know that the 80-051 is the part that i need...I have one broken at the top of my door. Yet it seems all you sell it in is white, which will stick out like a sore thumb on my door. The original clips are a brown color. I found the part on another website in a Tan color, but when I contacted the si ... (cont.)

I purchased the same 81-112 replacement rollers for a Peachtree Citation sliding door. What is the proper technique for (1) removing the bottom rail from the door; and (2) removing the old rollers? These rollers have never been replaced in 27 years! Thanks for your help. Tom E.

I would like to purchase two sets of window channel balances but I can not locate the correct one. I measured 1/2 inch track that is 25 inches long. I added pictures of the top and bottom clips I forgot to add this is for a non-tilt window. I think the part I need is the Series 380 with the ... (cont.)