Viewing all customer Discussions for:

Door & Window

Insert to wheel holder says #D-719 Says on it. This is for custom sliding closet mirrored doors 5/8" thick 2 3/8" x 1"

The windows are DH in a modular home built in eastern PA. The shoe is 9/16" thick x 1 1/4" wide. The window is about 38 x 56. Another window with single coil is 29 x 36. Sorry, I did not measure the coil balance, but I will need them also. I did not find any identifying numbers.

I have several windows where the channel balances have failed. They all look the same except are different lengths. I need one 31HD, 6 27TG, and 2 27C. Is that enough to determine which channel balances I need?

Hi, I am looking for the correct channel balance to purchase. The only marking on my current channel balance is 30C - I am guessing the 30" Series 795 Channel Balance is the correct item to purchase, but I would like to know for sure. Thank you!

We know we need to replace the operator on this window, but we would like to replace it with a handle that folds in. We think this is a Vetter window. Do have any window operators that have folding handles they would work?

Can you point me to the proper snap-in glazing for my windows? I have house built in the late 60's with Aluminum windows. The window panes are held in by grey snap-in "plastic" glazing. The glazing is a smidge larger than 7/16" wide (maybe 15/32"??). from the leading edge to the back side of the ... (cont.)

Can you help me find a suitable replacement plastic glaze

To whom it may concern. Attached are a few pictures of a spiral balance I am having difficulty locating. Parts a from a fairly old (1950s ish ?) single pane double hung aluminum window. Any help would be much appreciated. Thanks, Luke

For tilt windows

door purchased home depot approximately 10 years ago (?) locking latch broke off

I have Barrier double hung vinyl windows that are 19 years old. I need to replace the window screen frames and all after a hail storm. I need a very thin knife blade type clip to hold them in. I need 100 pieces.

Looking for a replacement for this pivot bar

One of the coil balances on my window had its coil bend and lock up. The Balance has three coils in it and two are in bad shape. I would like to replace the whole balance on both sides. This unit has one screw hole to attach to the sash. Can you show me what I need to replace these with. Also, I ... (cont.)

I am looking for a 31 1/2 Caldwell balancer

I am looking to replace a pair of window balances The number stamped on them is 2140 NK (see attachment RenderedContent-54D1AD80-2DBF-4222-87E0-CDA8F7DDB0EE.jpg) The channel is 22 inches long, 1/2 inch wide and 9/16 inches depth. I do not know how to identify the clips.

I need to replace 4 casement window hand cranks. Windows were made by RJT industries in 1997. model number on the window is G2-STRKR-*12 and inside the windows on the silver lining it says RJT 97 Roto-Frank supplied the windows to RJT of woodbridge, va.

I have truth window locks and wasn't sure if it would work because it's hard to go by with pics. These are more rounded and my originals have more sharp edges but it's just looks. Now there are exact truth locks for $25 a piece , but I tried these. Glad I did , took about 3 minutes to install. ... (cont.)

Help with parts

balance slides sizes

I have tandem 1-1/2" concave rollers. Problem: bearings becoming rusted out in 6 months. Track getting dirty and damp. I have 4 dogs that constantly come in and out 6-8 times a day. Is there any sort of plastic or ceramic bearings? Or some sort of thick brush I can put on the door to keep the tr ... (cont.)