Viewing all customer Discussions for:

Door & Window

Hi the number on the back of the thumb latch I have is s2573553 I think the replacement part number I need is 82-043. I would like to replace the key and cylinder for the lock. Which one would work with the thumb latch?

I have a right swing and a left swing window crank (only one is shown in the picture) that I need to replace. The black part should have a white handle connected to the end (that is the part that broke). The width of the mounting flange portion (where all the holes are) is 3 5/8". Both arms are 4 ... (cont.)

I don't see this part in your catalog, which is a first! Total length of part is approx 4.25"

Hello, Could you please help to identify the par by the picture? I am thinking 15-046, but not 100% sure. Thank you!

Trying to locate a pivot bar. This one is broken, and I attempted to glue it, but it isn't straight. Unsure of manufacturer. Thank you Karen

Please tell me what the part in the picture is. Thank you

I am told by the manufacturer that i have a Atrium weatherlock 800 series which they no longer manufacturer. I am looking for 4 replacement handles and they suggested i contact you for assistance Thanks in advance Bill B

This is for an aluminum window. This piece goes in on the bottom of the window corner to hold the balance in place. It looks like the end of the balance clips in there and it keep the balance in place and from falling out of the window frame. It has a white plastic piece that it seems goes around it ... (cont.)

Hi, I'm looking for locking handle for my window. Attached are some pictures. The "strike bar" broke off and is missing in the pictures. The measurements are: 3 3/8 inches between screw holes. 3/4 inch wide at back, 4 inches long 3 3/4 inch slightly curved handle Thanks for your help, ... (cont.)

I have milestone horizontal roller series 4000 windows. WIN 04801 florida window. not patio door. the assembly looks about 3/4" wide of the plastic inside the track, the tab on the outside of the track at the end is 1". with a single brass roller. I think that the roller was convex. If you h ... (cont.)

Hello Can you tell me which strike works with this screen latch? Im thinking it is "85-020A". Also, do you have the guide that keeps screen door on the lower track? Thanks Kirk

Will 82-316 work for lock replacement on 200 series sliding door that was bought and installed in 1987. And, if it will, will the thumb latch need to be replaced in order to work with this keyed lock? Thank you.

My windows are Simonton windows. They're single hung. They're white. Some of the parts are broken on the windows. I called the company and they said they no longer make these windows and referred me to you as a place that might have the parts. First two pics...0779 & 0780...are the same piece. Th ... (cont.)

Do you list the screws that would be used for certain parts you sell? Namely part# 90-139

We are looking to purchase two balance for both sides, we found this number in the balance: 731 B05 898Please let us know if you guys carry this part or if there's any other part that can work.Thanks in advance for your assistance.

The photo below shows a spring that came from one of our tilt in widows. Do you have this part in stock? The window will not stay in the open position, this appears to be the item causing the problem, or would it be one of the pivot locks? I have purchased parts from your company in the past. Thank ... (cont.)

My old locking handles had threads. I don't see any in these handles.

Ordered 95-011 : Internal Corner, 1/2" x 1/4", just thinner 3/16??

Hello and thanks for the sash balances I just bought. They were just the pieces I needed. However I found this broken piece. It's at the top corner of the sash and looks like it's supposed to be a stop for the top of the channel balance. It's broken so the channel balance protrudes above the sash. C ... (cont.)

Cannot figure out who manufactured the windows. I have strings broken on 5 of these I can send more pictures. Looks alot like S795-32 ( I followed the link from a picture on lin because it looked likr mine). Only mine is 36" long not 32".