Viewing all customer Discussions for:

Door & Window

I want to reverse my patio door and put the stationary part on the left, the slider on the right. The track appears identical inside and out. Last night I removed the screws at the middle of the door on the outside to see if the "finishing moulding" would just slide off. It does not, what is hol ... (cont.)

Hi- This is the mechanism that I need for an Andersen window. The # etched on the front is C-9400-1A. The number on the back is F-9400-8, with the letter "B" appearing beneath it. Do you have this part? Thank you.

What is the length of the handle? I am looking for replacement of a handle (in attachment). Will this match? holes 1.5 inch apart handle 3.5 inch locking part is tapered with slight notch at the end. Thanks S

I have "Mastic" brand windows. I've measured the spiral balance to be 19 1/4 inches and 7/16 inch diameter. The balance I currently have in the window is covered in a plastic casing...I'm hoping that doesn't make a difference. It looks to me like I need the 900 series, blue tip. Does that sound c ... (cont.)

isuccessfully installed the 15 046 and the s600 29 in my window project but the pivot bars are completely rusted away. They are attached to the window with a single screw,into an adjusting slot. the old 15 046 matched the new ones perfectly. can you suggest new pivot bars that will work with this ... (cont.)

I need to replace my traditional Truth casement handles (covers like item 39-323) with fold-down handles to accommodate new blinds. Can I use items 39-375 and 39-376? If so, which one goes on which side of a paired window?

Your closet mirror door wheel is part # 23-198 However, see my photo attached: The flange sticking out just above the 'phillips' screw head on my part is straight: On your part it is angled up 90 degrees and has a hole in it. Are the parts interchangeable? Thanks for your attention to t ... (cont.)

Just bought this house and have several window coil balances broken. Not sure what type of vynl windows I have but they tilt inside. House is about 12 years old. How do I determine which replacement parts I need? Pictures below Thanks, John

Hi ...I need the following window parts...two 27" window balance channel tops and two plastic parts on the top of the sliding window which meets the channel tops I uploaded pictures with measurements...so I need 4 parts in all...thanks

Hello, I need 3 pairs of OBND0001. Can you help?

I have what appears to be a Series 770 29" balance stamped 29C BSI KH where the BSI is vertically imprinted between the C and the letters KH. My channel depth is ~1/2" and width seems to be ~1.25" wide. I need 2 new bottom shoes. I did use screwdriver and turned black circular piece in Pictu ... (cont.)

I need two parts for a Pella hinged screen door. I do not know the model number. It came integrated in a pre-hung patio french door unit. I've managed to repair the spring on the door latch, so now all I am looking for is the slide that secures the bottom of the other door (the one without the ... (cont.)

Please help me locate and purchase a metal sliding window lock as pictured in attachment. Freddie Fix It

Kolbe windows installed in 1995. Please help There are 52 windows. Not sure how they are called out properly but from the inside as I look at them I have 27 units with the crank/hinge on the left side and 25 units with the crank/hinge on the right. Listed below are the part numbers I believe a ... (cont.)

Hi I have Anderson window with a counter balance number e149p27574 are parts available? Niek captein

I have to replace ~30 balances for my Peachtree Ariel double hung non-tilt windows. I bought the windows in 1985. It looks like I need your S745-20, weighted for 13-17 lbs. But before I pull the trigger and buy them, can you confirm that, as far as you can tell, the S745-20 will probably work? ... (cont.)

I have a Barber and Ross Casement window in my kitchen that was installed when the house was new in 1995. The crank can open the window but when you turn the handle to close it, it just spins. The kitchen as two windows that open out from the center with two cranks and both have the same problem. I ... (cont.)

I have attached some photos of the casement hardware that I need to find out if you carry in your inventory. please advise. thank you.

i need bottom guides for a radco sliding windows, but i do not have a sample. you carry the top guide (87-198). any help would be appreciated. thanks george

Sliding patio door snap in window glazing aprox 7/8" X 10/16" see pix. I could not find on your site. Door made in the 70s. thanks Jon