Viewing all customer Discussions for:

Door & Window

Need to replace window latch for Capitol(MIWD) dble. hung window series 650 white

PLease help me out. Your website is helpful but all the end parts look the same to me. I have a balance that I need to replace. It is ink stamped 25 5 LQ CALDWELL. The metal shaft is 1/2 inch wide and 26 inches long. thanks!

Hello,I want to order my window operator , but i am not sure which one I have to choose. in my window operator says four numbers: (two on the front and two on the back). On the front says: 1361486 L 1361483 HCR On the back: 1361485 R 1361482 HCR Also, I do not know whi

I am trying to locate 4 sliding glass patio door bottom single wheel roller assemblies for two 25 yr. old patio doors (no manufacturer name on doors). The wheel is metal and convex and is approx. 7/8" in diameter. Hopefully, you can read the measurements off the photo. Thank you very much. Ir ... (cont.)

Hi, I am looking at your 90-005 and 90-009. Are they interchangeable or am I "hosed" if I order the wrong one. I think that the 90-005 is the one I need according to your picture (it has no ridge along the edge of the lock piece......). SUNAIR ALUMINUM CORPORATION

I need to determine if top sash guide is required for balance number 2230. I also need to replace the channel balance top and channel balance shoe and believe these parts to be channel balance top as 19-002, and channel balance shoe, winged as 15-005. I also need to replace take out clips which I ... (cont.)

Please provide an estimate for the following 9/16" window balances (photo's attached): Note: The length measurements are for the metal channel only and do not include the additional length of the plastic hardware. 18 each - 9/16" x 25" (18lbs window) 4 each - 9/16" x 25" (22lbs window) ... (cont.)

I have a sach balanace to replace...its stamped as 27 4 DN CALDWELL. Its actually 28" long. Can you help identifying my part and maybe you have a full kit that you can sell? This is a '95 built house, so I'm sure these parts are about that time old. Thanks much, Erez

I bought a house that has Pella replacement tilt in windows. There is a part located on both sides of the upper window that keep the lower window from opening more than 2". A few of them are broken so I'm hoping to replace them. I have sent a picture as a referance. Thank you. Julie ... (cont.)

Thank you for posting. I'm sorry, is this for an Andersen window? If so, please see our 24-637 Andersen Sash Balance, which can replace balance boxes with the stamp 6#23.

Good morning, I'm looking for two 27" sash balances and a latch for two aluminum windows. I've attached images two of each end of the sash balance and the latch. On the balance near the end is "27 4" as well as, in smaller print, RN then BS1 printed sideways and 7H. The latch body is 3/4 x 2 13/1 ... (cont.)

I have nu prime windows by season all and I am trying to replace the valences in the sides of them. I am not able to pick a picture I like on your site. They are 23 inches long. They are 1/2 inch wide and same deep. I like the looks of 380, 385 and 390 but they do not appear to have the bottom I ... (cont.)

I have taken pictures of the roller mechanism that I need replaced. Please send a reply email indicating the correct replacement from your company (please include part number). I will need 4.

My broken balance is 28" 2740 Top is 19-005, Shoe is 15-003 I need two balances. Can you tell me costs.

Hi, I need help identifying the correct pivot bar shoe for my PGT window. The window was new in 2005 if that helps. I've attached photographs and measurements. I need one each for the left and right side.

I bought a home and it had one window that was missing a channel balance I thought would be a minor repair. I matched up the remaining channel balance with the Swisco balance and ordered two new ones. I installed them as your video shows and all did not go well. I was barely able to get the lif ... (cont.)

MALTA is the logo new in 1979. I have two windows that need replacements. I don't need to match the brand and can get someone to recut any woodwork if necessary.

I'm having trouble locating these and was hoping you could help. I need 4 of each type of balance (see pics) for Milgard DH windows. I'm looking to get heavier springs because I installed sound glass in the existing windows and they are a bit heavier because of the laminated glass. ... (cont.)

I need to order channel balancers and the plastic stop channels for my windows. See images attached

In repairing the stained glass panels at our church, several parts were either lost or broken for the tilting mechanism. There are 3 pieces on each side of the window that make up the pivot point. There's a non-slotted screw that provides a pressure point for the set screw. The non-slotted screw ins ... (cont.)