Viewing all customer Discussions for:

Door & Window

We have cheapo aluminum screens, and the slot where a leaf spring would go is slightly less than 3'16 in. What springs can we use, and please indictate how they would be installed. Thank you. Jim

What is the width of the base for the handle? Also will it work with a 5/16 spindle? thanks

I have attached a few photos of the pivot bar that has snapped in half on a couple of our windows. I took the window in to get the glass repaired when it fell and not one company could tell me the manufacturer. I bought the house 5 years ago with these windows. I searched your site for pivot bars an ... (cont.)

The balance is 11 in long when excluding the two plastic ends. Each plastic ends have "wings".I've seen the top end on your website but don't an identical bottom piece. The # stamped on the metal channel says 1020 and it's 1/2 inch.Pictures are attached. Thanks for any help you can provide. John ... (cont.)

My house has about 16 casement windows and screens with really cheap plastic retainer pins that seem to break if you look at them wrong. Forget trying to remove them for cleaning. Can you help me identify what I need? I have no idea as to the original manufacturer of the windows or screens, as we ... (cont.)

Thanks for posting! Please take a look at our 24-1033 Andersen sash balance, which can be used to replace balances with the stamp 10#31.

patio screen door latch width of latch 2 inches height of latch 4 inches between two screws on front 3 inches is needed On this latch there is a black tab that is supposed to be on silver part. This part is broken. Janet

I need some window balances for my tilt vinyl windows that are 7-8 years old. The only marking on the windows is AWS etched in the corner of the window. The balance is 28" long x 5/8" wide x 1/2 " deep. The window glass is 30 3/4" w x 26 5/8" tall. The balance marking is DB102 in small letters ... (cont.)

i need to replace a ( part no 28 3 Caldwell ) channel balance ,,, the metal part is 29 inches long . Attached are 4 photos of the channel balance .. the metal part is 19 inches long I will need two, might as well do both sides .... if they work better, I will probably replace others before they b ... (cont.)

I'm looking for weather strip for a bay with swing out windows. Installed mid 80's. I'm not sure what brand window. Your weather strip shown 55-106 is similar except mine is 1/4 x 1/4 x 5/16 "U" shaped.

I have looked at your pivot bar selection and can't seem to identify this one. Its three inches long Any help would be greatly appreciated Thanks Ray

I need replacements for two different size balances for my Peachtree non-tilt Ariel windows. One size is marked 3660 L J Caldwell. This one measures 9/16" wide X 5/8" deep with a 26 1/4" overall length. The metal on the long edges of the U-channel is doubled over. The other is marked 2448 BSI an ... (cont.)

I am trying to replace a dual arm casement window operator. The window is small and having removed the old operator the long arm is about 7". Everywhere only seems to have a 9" long arm. Can you supply one ?

Crestwood Windows purchased at Home Depot 1996 I need: two - handles #45054 five - covers (no number) Color described as pewter on original invoice. Any help would be greatly appreciated. Thank you

Hi, I am looking for the clips which hold my window grates on to my window. My windows are approximately 15 years old and I am unable to tell who the mfg. of the window was. I do have a few of the clips left. Attached is a picture. Can tell me if this part available? Thank you, Brett ... (cont.)

My house was built in the 1987/88 timeframe. I have a Pella sliding glass door with worn roller assemblies and worn nylon/plastic parts. The roller replacement part here at Swisco has product code 81-098. I need identify the other worn out parts. Attached is an image of one of the two white ... (cont.)

I am in need of window release latches for vertical sliding windows. Can you help? Big Jim

I'm a handyman and have a customer that has aluminum tilt windows. I cannot find any manufacturer information on the windows. The latches are white, surface mount 3" long X 3/4" wide. What do you recommend? the 3/4" width is probably the most critical since the windows are only 3/4 thick. ... (cont.)

This handle set has it's mounting holes 6 1/2" center to center. Do you know this item? Thanks! Andrew