Viewing all customer Discussions for:

Closet

After I installed the newly purchased pin cap #21-108 & all nylinders, I feel that the nylon guides are very tight. It takes a bit of effort to operate the door. Your replacement part seems identical to what I replaced. What's wrong?

Trying to find this part

I need to identify, and then order a pin for a Fenestra bi-fold closet door. While in place, it measure 4.25 inches in length. I, unfortunately, do not have a picture of the pin uninstalled. If it helps, the door itself is 93.5 inches long. Thank you, Kevin

I am looking for a track similar to the one shown in the picture. It is 72 inches long. This one was bent from being stepped on. Are there any stronger alternatives? If not, do you know which replacement part would be the best replacement? Model 23-242? Thanks, Greg

I need help finding exact replacement parts to fix a bi fold door.

I am interested in your HD Hanger pair. Is there anything that is similar that can handle more of a weight load? Can the track be sold separately? I need about 40

American Building Supply Inc. CAT II 400 lb impact strength, aluminum frame. Wheels in bottom of door, riding on floor track.

Hi! Just to confirm, from reading other posts I am gathering that Stanley door 4011 hardware is replaced by swisco part 23-041? Our little plastic wheel is looking quite flat on one side, so that should fix it! Thanks so much!!

EuI need pins for plastic bifold doors for my condo in Florida. The doors probably go back to the 1970's. The pins would be similar in style to the Barton Kramer # 118. However, this part does not work. Can you help? Thanks Bob

Here is a picture of the bottom pin. It is the wrong one as it is too small for the groove. It should be 13/32" wide to fit the groove. Can you help?

The corner of rail is cracked. The rail width is one inch, however where the rail is crack it is 1'1/4-3/8". The rail is 35 1/2inches by 1 inch wide and half inch depth. The rail she'll installed in closet door is 7/8". I need the entire rail, plastic rail wheel (7/8) and any other hardware you ... (cont.)

Hi- I am looking for replacement for these sliding closet door rollers. The rollers diameter is 3/4" and width 1/4". The offset for the Back panel is 3/4" and Front panel is 3/8". Do you offer anything like this or have another suggestion that can be used in place of these? Thank you. C ... (cont.)

6 needed

Hi, there are not numbers or manufacture on this piece. I need to order several of them. Is this something you stock. Thank you Roseann

I have two sliding doors that are driving me crazy in a house I just purchased. From you catalog I have confirmed that 23-024 and 23-025 are the correct hangers from measurements, and appearance; however, on my application, they are not technically hangers they are at the bottoms of the doors. ... (cont.)

hi, here are two photos of the wheels I need. O.D of roller is 1-1/2" distance of the mounting holes, left-right 2-3/4", top-bottom 2-3/8 . the mounting holes are positioned at half the thickness of the bracket and the slider is 1-3/4 wide and 1/2 thick. I would be prepared to simply c ... (cont.)

I need several replacement mirror wardrobe door roller very similar to your Product Code: 23-064. There are some differences (e.g. my wheel is 1.5 inches) but the key similarity is the the ledge that sticks out to hold the door. I have looked everywhere but have found nothing that is as similar as t ... (cont.)

Need replacement floor track for Stanley Monarch sliding mirror doors. 60". Please see attached photo.

I am not sure if these are your parts. There are no markings, but it is the closest that I could find on the internet.

Here parts I need to repair the doors for my brother in law. First is a photo of a diagram and a bottom pivot pin assembly. I am hoping you can get all the info from the drawing for the parts. I would need. I would like to replace all the parts on the doors if possible. Our tracks appear to be good ... (cont.)