Viewing all customer Discussions for:

Drawer & Cabinet

Are these flexible so you can bend them to take out the drawer or do you need to completely remove these to take the drawer out. Also, can you place this on the bottom of the dresser and slide the drawer over it. Thanks,

Hi I need the pair of rails with the offset piece molded. The length is 22 5/8. I don't know the manufacturer. I hope you can help. thanks!

I have a china hutch that is in need of glass retainer clips...not sure if your 32- 325 will fit or not. Can you help me? I have attached photos. Thanks

looking for this particular sort of drawer guides,,

Have a rear drawer mount that has broken. Could you tell me which one of your products would closely match mine?

I am in need of two kitchen cabinet hinges marked with Made in Italy, 80059, H-2. It also has letter "G" written on it. I have attached herewith 3 views of the latch. First shows how it is attached to the cabinet door. The other two are front and back views of the latch. The other markings are d ... (cont.)

I researched online the appropriate replace for my window operator. I ordered the 39-278. It doesn't have two holes at top nor a threaded arm. I called Customer service and they asked me to send pictures. Please let me know my best replacement peace.

Markings: uppercase G, also uppercase A. The number 6600 is also stamped on the part.

We already ordered Grass Under-mount Slide Locking Device Kit from you, but now we have discovered that we need the mounting bracket part that goes connects to the drawer itself. Then we will attach the Slide Locking Device into that bracket.

I am trying to find a 3/4" wheel that I can attach to left side of these pictures where the wheel is missing (original was put on with a rivet but I need a screw based one now). Alternatively I could purchase a new set of rails if you have 20" with the L-shape at the end (I have not been able to ... (cont.)

Looks like a number of people were interested in replacing #452 guide with a similar part from your portfolio. Any good matches?

I have a bunch of kitchen cabinet drawers that have two pegs that fit into the cabinet fascia piece. Needless to say, these detach all the time so I end up with the cabinet face in my hand. I am looking for some corner braces that will hold the sides and bottom piece of the cabinet to the fascia ... (cont.)

It has "R1" stamped on it. The dowels/pins fit into holes in the back of the cabinet.

Pennsylvania House drawer chest and armoire - purchased around 2007. Opening at base is 1 1/4". The top part of the glide is 2 1/2". Opening where wood on drawer slides is almost 1 1/4". Please let me know if you have all the info you need and if it is clear. Any help would be appreciated. Thanks. ... (cont.)

I need a drawer roller track replacement,this picture shows the original,thanks,is 21"and 3/4 long 3/4

I need a pair of rear drawer track sockets. However, I need your guidance. The ones that I must replace look exactly like your product code: 32-012. My broken sockets seem to be a little larger than this pair. Remember, I am measuring broken parts, but my approximate measurements are: 21/16" x 9/16" ... (cont.)

Bedroom set was purchased in 2002. 'Universal' is the make. The drawers insert with a center middle track and a plastic glider on each side of the area where the drawer inserts. It is a little over 1.25 inches long and screws in to the dresser. It is l-shaped but has a triangle type piece on the ... (cont.)

Trying to help a friend locate hinges for some Brammer cabinets from the 70's. They are face frame mounted non self closing and the base of the hinge that mounts to the door and the exposed face mount are flush when the hinge is in open position.Can anyone be of any help?

Can you also use these for cabinet drawers?

Looking for Grant drawer slides for a desk drawer. The slides measure 22". We are trying to obtain one complete set (for one drawer ). Any assistance would be appreciated