Viewing all customer Discussions for:

Other

Spring balance for both sides of a window. 20c is on the piece. It is 20 inches long. These pictures are the piece in the window and out of the window. There is 2 pics for top and bottom. If this does not help, would we be able to mail the piece to you so you can match it up.

I am unable to identify window manufacturer as the window is too high

I need replacement parts for all the latches in the apartment. I need which set to get.

Patio sliding door roller

Hi,I'm sending 2 separate requests: this first one is for springs for a bedroom window, the second will be springs for living room window. Your YouTube video said I needed 7-8 different pics but this form only allows upload of 5 pics. Please let me know if I need to send additional pics.I need sprin ... (cont.)

Searching for drawer guides for the top of a bar cabinet chest. The front of the guide has patent 2857233 and the back has RONTHOR N.Y.C.. I have had the bar for 47+ years and there are no identifying labels or numbers on the cabinet. It is solid wood. The runners are on the bottom of the counte ... (cont.)

Top Sash Guide dimensions are around 15/16 in x 15/16 in on top part and 1 1/8" height. The metal stopper is about 1" I need about 14 sash guides and stoppers.

I know you have several different series and I want to make sure I am ordering the correct one. The length of the metal portion of the channel is 28 inches long and the marking on it is 2740. I have submitted four pictures, two of each end to make sure you can recommend the correct replacement part. ... (cont.)

I have some windows that have suffered from a balance coil component failure specifically the nylon bushing that supports the rods on the bottom of the lower window sash and need to order the correct parts to repair the windows. Any information regarding removal, installation and correct part identi ... (cont.)

Hi I need 35 drain covers for BFRICH windows . The hole in window is 1 inch wide by 3/8 high they have a flap which lets water out of sill area.

In each photo the left side channel balance is what I ordered, the right side is what I have. Clearly I ordered the wrong thing. Please help me identify what I need to order to replace my existing channel balances.

Please provide item numbers and pricing for the left and the right window coils.Constant Force, Steel, Unfinished, 2 57/64 in Lg, 43/64 in HtI need to order 12 of eachThank you Narcisa

Attached are two photos of the small plastic window lock on our ten year old window. Do you have a replacement piece that can be easily snapped in?

Hello: I'm looking to replace 2 broken splines/handles etc for my GU casement windows. This house was built in 2006. Could you please tell me what I need after looking at the attached photo? I need for both the left and right side of the dual windows. A photo of the left side, looking from inside t ... (cont.)

I have flush mounted sliding glass door handles and want to install pull handles both inside and outside. Is this possible? looking for white. The current distance between mounting screws is 6-5/8 Thank you Paul

hi. I cannot find any numbers or names on these broken pieces. the windows themselves say simonton on the locks. clearly the metal 'spring' has snapped! can you please help me figure out which parts I need to order to replace and make our windows work again!

I am looking for what part I can use to replace one of these folding crank handles. I can't seem to find the exact part but even if you can point me in the direction of something close I'd appreciate it!

I received #15-211 pivot shoes, 17/32"from you and they fit fine except slot to accept window pivot is different. See photo. I was able to use old part as shown. Do you have 15-211 type with desired configuration. Thank you.

Referred to you by Harvey Windows for replacement parts for door handle for my storm door. Grandchildren hanging on handle. Does not respond for opening/closing to latch door closed. In need of indoor piece as outside still working OR full set. Current drill holes are an out 2" apart with slightly l ... (cont.)

We have a broken pivot bar looks like just 1 hole do you have??