Viewing all customer Discussions for:

Other

This is 2 5/8" long. The top is 11/16" wide. The bottom is 9/16" wide. The height is 7/16". I don't see the same one on your site, but I may have overlooked it. Our house is about 20 years old, so I imagine these latches are also about that age.

Please let me know if you have this part or one that would work. I don't know the brand of the windows. I live in South Florida and the house Was built in the early 90's Thank you Kurt Sampson

This is for a window that was put in my home back in 1998. It has a part number on the channel labeled 2330. It is spring assisted pulley. What channel part do I need? The entire pulley rope has dry rotted and broke.

I'm not shore you have the same item I ordered one from home depot but it wasn't match with this, please help me to find same lock thanks

Hello, was wondering if you could help me identify the correct parts. The window is 33"W x 30" height. It weighs 10lbs. The number on the spring balance is 2810. The spring balance is 29" long, just about .5" thick (little more) You can see the bottom in the pic. The top has two "wings" and an unkno ... (cont.)

I have a NAMI window NC2200/NC2400 with two broken tilt latches. Do you have replacement latches for that particular window?

I ordered a part, but it is too thick. Does not fit into the screen frame. I am returning the part. Please let me know if you have this piece. Thanks.

this part is on both sides and you pull them in to lay the window down both parts slide out of the top

My Anderson window needs a new window balance recoil box, Looking at the Anderson chart, My window measures, APROX. 36.5 WIDE APROX. 23.25 HIGH THE CHART CALLS FOR A 1031 BALANCE BOX,the pictures should show the Anderson etched stamp Can this be correct?

I need at least two of these maybe more haven't gotten to all my windows.I need to know the correct top sash piece that screws to the window frame to receive the balance.The balance has 2950 B61 swisco stamped on it.

I'm looking for the interior bracket that connects the bottom rail to the side rails on a screen window.

Good Evening - First, thanks for your helpful videos and postings on door hardware. Second, I have a broken patio door lock latch. (Fortunately it is broken in the locked position.) The attached pictures seem to match an 82-089 handle system. The problem is, I need only a bronze latch lever and ... (cont.)

Do you sell parts for Metal Window Corp doors - 2500 or 3000 series? Thank you. Monica

The window is insulsash, I need to replace the tilt latches but I'm not sure which exact part I need. Can you help? These are photos of a latch I took off

I have older windows in my home and many of the windows will not stay up when open. There is no numbers or identifiers on the window parts. I believe I need new springs or the whole unit. Can you help me identify the parts in the pictured shown.

Hi All, I do not see any markings on the roller assembly. It is well made vs all the replacements I have found in Home Depot, Lowe's, etc. The roller diameters are 1 5/16". Overall fastening hole center to hole center is 5 15/16". The rollers are made of solid metal. The sliding door is very ro ... (cont.)

Good morning guys,I need window balances to be replaced. They maybe CB 1050 type, 1/2" wide and 1/2" deep. Metal channel length is 21".Channel is marked - (09/04) UNIQUE 20-C-30. I need 8 of them. And advise how is the best way to install them.Marc

Print on old balance is 26-4 GG5 CMC 54 Length is 27 inches Width is .5 inch Looking for the right replacement?

Broken window lock

hello, I need help getting a replacement part. I believe, from my research, that these windows are MW windows circa 2003, double hung wood sashes, vinyl jamb liners. The plastic piece in the channel in this photo is broken on another window and I need a replacement as the sash tends to sag and leav ... (cont.)