Viewing all customer Discussions for:

39-092 ROTO Casement Operator

The crank system on our milgard casement windows has stopped working (appears like the internal gears are totally worn down). Would like to buy a replacement part and fix it.

hi. i would like to locate and purchase some Milgard series 3510 casement / product line 032-167 window operators to replace my broken ones. they feel "stripped" and will not open the casement windows any longer. one casement window is 35" wide x 37.5" tall, and another one is 35" wide x 49" tall ... (cont.)

Kitchen window. Right side (from interior) open. Crank stops and gets stuck before closing. Which crank part should I order?

Is 39-092 the right replacement for the attached image? Thanks!

I am looking to buy 4 of these handles for my Casement window Operator (Milgard series 3510 window) with 5/16" spline. The spline has a hex shape. Not having much luck looking online. Do you have something that would work? Thanks.Dan

Will your casement window parts work on wall side replacement windows and if so which ones would you recommend the hinge bracket broke away from the operator. I have 2 of these windows and both are bad Thank you for your time Dan

I'm look for a similar operator That o can use it to replace the broken one

I believe my bronze, right 20 wide x 44 tall casement window is a Superior Window Products. It was installed in 1997. I believe that Superior Windows was acquired by Atrium Windows (aka Hr Windows) in Texas The riveted stud broke off from the stud bracket. The crank assembly works fine. I would ap ... (cont.)

Roto engraved on bottom, installed in 1998.

The gears are strip. Need replace

I am looking for replacement parts for the crank type openers above. I have been told they are for Certainteed windows but I cannot confirm that. The brace has the words "Interlock World Pats" and the number 1090.

I need to replace the hardware at bottom right, shown in an inverted "T" configuration in the attached photograph. It appears to be something you manufactured about 20 years ago (that was when it was installed) and the arm shown top left connects to a crank actuator very similar to 39-092. --Coli ... (cont.)

I need to replace a couple of crank handles on my casement windows. The windows were made by Certainteed and installed about 15 years ago. They are almond color. The crank assembly works fine but the handle has broken and I want to be sure that the replacement handle will fit correctly onto the he ... (cont.)

Talked with Tim on Friday four each right and left hinges and cranks

I need a replacement for the assembly, the inter cog has broken teeth. It is a Roto P4600 (see picture). The cut in the window is 5inches long and 0.5inches high. The width of the portion with the screws is just shy of 4 3/8 inches (about 4 5/15 inches). The spacing for the screws is 9/16 inch on ... (cont.)

I am looking for a white metal replacement arm and black plastic connector. These came with Milgard casement windows c. 2010. The handle had begun to spin without operating the window; when I disassembled the arm I saw that the plastic piece had become stripped.

Looking for a manufacturer and part number so I can replace one on another window. The part I am looking for is the top silver one that screws to the back corner of the window and has a slide clip on the other end. Any help is appreciated.

Hi, I have original casement windows on a 1990's house. They are hard to crank open and then impossible to crank closed. I have to push the window closed from the outside. The handle has a code of P4601. The window locking system is working fine. I have 4 windows. Which parts do I need to replace? T ... (cont.)

I am attaching a picture with measurements of the pieces as well. I need three of the long pieces and three of the C clips as shown in photos. The bar is approximately 5 3/16" and the c clip is approximately 1 1/4".

Both right and left.