Viewing all customer Discussions for:

39-278 RH Awning Operator, Nu-Aire

Hi there, I have no idea what type of windows I have and what type of replacement crank to buy (I need 2). I hope you can help! Thank you! Callie

My crank windows are on the porch of a 1960's modern ranch home.1

Marking inside housing are PAT. No. 198 202 U.8 - ?8 a bit worn; 2 R.H. RD1963 CA There is also a square with diagonal lines from each corner with .06 stamped in the center. This is on the inside of the top corner of the housing. Dimensions Operator link holes are 2 3/4" apart. Has Nylon bushing ... (cont.)

Looking for a replacement for a number of operators in my old cabin. let me know if you have any questions, please. Picture 2250: Distance from Main lift arm operator body hinge pin to articulating small arm braded pivot = 2 5/8" Picture 2252- overall center/center of small arm pivot hole = 2 1/8" ... (cont.)

There are no names or part numbers on the existing crank. I ordered 39-060, the Keller window crank, hoping it was the right part. It is not. The case appears the same, but the arm is shorter on this one (~5cm) and the hole that attaches to the window arm is wider in diameter (~1cm). Serves me r ... (cont.)

Attached are pictures and dimensions of a window crank operator that I believe is or close to the 39 - 084, but there are some slight differences. The 2 holes at the bottom measure a center to center spacing of 1-3/16" whereas the dimension you show is 1-1/8". The arm extension has a clearan ... (cont.)

I need 5 of therse window cranks IH CO 790.

Hi, The crank on my window shutter is broken. In the pictures attached, the part that I use to the close the window (crank) is separated from the body and won't latch on. The crank was able to open the window further but not close it. I had to put bricks on my blinds to keep them closed ... (cont.)

This is from a house that was build in 1925. The arm that comes out of the box does not protrude out of the box when fully close which makes it difficult to identify the correct window operator. From what I could measure, the arm that is connected by the screw is about 2 3/8 in length.The space betw ... (cont.)

The mount on the crank housing broke and the worm gear that attaches to the handle came out. I jerry-rigged it and got it to close. Is a replacement available? I'll need a right and a left (so they match. Thanks.

Trying to locate a replacement for the pictured window crank. Approximately 50 + years old

Help

Unable to find replacements at any local stores. Can you help me out? Thank you. Gabe

NUMBERS STAMPED INSIDE OF CRANK HOUSING. PAT. NO. 198202 US 2 R.H. RD1963 CAN. STAMPING ON INSIDE OF HANDLE 11500-11

I have a need for a window crank which I believe is a right hand version of Product Code: 39-026. Are there any differences in these? The one I am replacing has no markings nut is stamped KD JAL on the inside of the tabs where is attaches to the frame. It is silver in color , not white, but color ... (cont.)

These jalousie windows are from the late 70's. I would like to replace the crank and get them working againMack

Will one of your products replace this? Is this a right or left crank? Thank you

I added two photos one of the opener and the other showing the hole locations on the window. The numbers I sent in my previous email is from the old handle. When I bought new handles the holes didn't align and that's why I need the exact model number as I have now.

Can you help me on this? I am attaching a picture of the part I need to replace. Do you have this? I measured the following: 5 3/4" long 2" deep 1" wide If you have the part I would like to order it. Much appreciated. Best regards,

Please see pics attached. I need help identifying the correct replacement please. The distance from the top screw to the bottom is 5", and the distance between the 2 bottom screws is 1".Also, the piece that connects to the window awning is 2.75".Thank you!