Viewing all customer Discussions for:

16-002 Take Out Clip

I have 2 windows I need replacement parts for in my home. I have attached a picture of the label and window in the dining room that I need the sash guide on each side, the plastic pieces and the metal clips. Could you provide these parts?

Clip in the frame of a milgard window that flips out to release the pane for removal and cleaning. Small metal piece that bent and broke. no identifying numbers or marks. I hope to buy a few in case i break one trying to replace it... they are flimsy.

PGT SINGLE HUNG BALANCERS NEEDED #6SHSTKR INKED ON BALANCE: 23-2 DW CMC 4 THANKS VERY MUCH, BOB

Part Number listed on Channel is 26-4 KG5 CMC 54 This is the only numbers listed on Channel

Four 28" x 9/16" (1/2)? Window weight 24lbs confirmed Missing clip in window frame Photo attached Old balance markings 27 4 BSI Photo attached

Hello Do you sell these? Thanks

I have two (2) balances that are in need of replacement. The attached photos are of the first. It is 1/2" wide and 28" long (metal to metal). The sash weighs 35 lbs. I am in need of 4 of these.Thank you,Bill

Hello, do you sell these clips that snap in and out from the channel and grab onto the sash balancer? If so what is the part#?

Hello! I have some windows that are at least 20-30 years old, and some of the balances have busted, and some are just really difficult so open and close. I'm capable of removing and installing the balances, but I want to be extra sure that I buy the correct replacements. The metal shaft of the balan ... (cont.)

Numbers on my channel balance are 26-3 kx cmc 11 The metal part of channel balance measures 27inches. I need 2 replacement parts. I will also need 4 new takeout clips to go with these parts.

Hello, I have 3 windows were 1 of the 2 channel balancers broke. I am looking to replace them but having a hard time matching them to find the right replacements. Two are on the same sized window but one is on a thinner but taller window. All three are identical top and bottom with the same 'hoo ... (cont.)

Also need clips for it as well as locking latch. Vanilla windows

Measurement is tiny bit less than 18in.

Sending some photos and hope this will help. Looks to me we need bottom fitting 15-193 and top fitting 19-038.Good morning. I have weathervane windows and need some channel balances replace with broken springs and another parts.In 2017 ordered some channel balances from You but cannot find any info ... (cont.)

I believe I purchased vinyl windows from Home Depot 2008/2009,also I believe the the brand to be Jeld-Wen. Need The Following: 4ea complete Balances and 4ea take out clips. PS: will send addition pictures.

Hi,Photo is of a window balance, part # 2830A. Balance is 5/8th of an inch x 29 inchesDo you have two of those and two take out clips in stock? If so, what is the cost?Thank you,Jeff

Kinro windows for a (RV) park model 371 purchased in 2019. I measured 9/16 width and 27" length. Windows are heavy. Sash weight model needed is requested. I need : 6 no-tilt window channel balances 2 take out clipsAndrea

I need a window balance similar to the 390 series, 2820 which is 29" long with one exception to the 390. My shoe depth is 1 3/16". Can I get a similar assembly with a 15-003 shoe installed? I would want a quantity of 2 balances and two take out clips (16-002).

I need 2 load balancers with plastic ends and inner workings. Basically I need a full complete replacement. It's about 27 inches long. Also need the take out metal clips located above corners that hold the load balance in its place.

19x1/2 long 1/2 wide