Viewing all customer Discussions for:

16-002 Take Out Clip

I have a channel balance that broke, along with the "clip". Can you please advise and what I need to purchase for the replacement parts? The length of the metal channel is 27.1" The stamp along the side of the channel states: 26-4 KC5 CMC 45 All the pictures showing the details are attached. Than ... (cont.)

I am looking for a channel balance replacement. Here are my pictures Stamp is 2090 25 Channel is 20" in length Also, if you could throw in a takeout clip that would be great.

HI! I'm so glad you are there! I'm trying to fix a double hung track that measures 28" long with a 12" spring end to end (w/hook). I purchased the window at Home Depot in the fall of 1997. There is a marking on the track itself "2630" There is a marking on the metal piece that encases the double pu ... (cont.)

Hi - these pics are from the one window with a 19" balance (actually measures 19.5) I also have 7 windows with a balance stamped 25 and that measure a little bit longer. I currently don't have pics of them. All windows are matched, same manufacturer and appear unmodified. Need to replace balances in ... (cont.)

one of sash top guide is broken (pictures show good on the left and bad on the right with front view and side view) Also show how top guide fitting into the window. The sizes are: Width = 5/8", Length = 1.5" (more in the picture) This is for Milgard window (single hung, non tilt), W ~3.5", total ... (cont.)

The stamping making is 29 per photo, the total metal stem is 30 inches. Which part number should I order? Also do you sell the clip that goes into the window side, as I am missing one? I also need to order similar with the stamp marked as 33 and the metal length is 34 with similar ends per attache ... (cont.)

Hello, I had an incident that destroyed both balance springs in my single hung window. The window has a placard that identifies it as a series 1500 SH, model H-LC25-48x96. The windows are non-tilt and use channel balances that are 1/2" in width. The 'heel-to-toe' measurement is about 1 3/32", and ... (cont.)

I need to replace the sash balance on my sliding window. From the pictures and descriptions, this looks like the right replacement part. It is a Vantage vertical slider 287-N-024. I have a couple of questions. - The guide on the web page says the metal channel is 14" long. The old metal channel m ... (cont.)

I'm not sure if this is the correct place to pose my question - but here goes it. I am unable to remove the sash and replace the channel balance, as the 'pop-out' clip is missing. What is the best alternative method to keep the channel down as I raise the sash? I have one side free, but still cann ... (cont.)

Hi,These are off Hallmark windows. I have one broken one so of course the sash balance doesn't work correctly with the missing piece. Do you have a source for these? I could use a few along with several replacement balance removal clips.ThanksSteve

I want both left and right replacements for our Caldwell Side Load Channel Balances along with 2 replacement take out clips. The only marking I can read is "Caldwell 26 4 AR" on the broken balance. The 26" reads along the metal rail only. The window is non-tilt. The rail measures 1/2" width on the t ... (cont.)

Hi - hoping for help figuring out what i'm missing. I've photographed each of the pieces -- the two side slider things -- plus the window. But it seems like i'm missing some clips on the window frame to keep everything in place. But there reality is i don't have a manual to show how things shoul ... (cont.)

Hi, I need 40 sets of the items I attached.

I need 4ea channel balance 2730. I think there is some plastic stops missing from my window frames for the channel balance's . When I look inside the window frame I see a square hole on top and a round hole on the bottom. I think there is supposed to be a stop in the top square hole but not sure. Wh ... (cont.)

Hi I'm needing to replace some channel balances. They're marked 3330P and 3320. The width appears to be 1/2", depth is 5/8", length is 34" (not including the plastic parts on the ends. Also need new take out clips, they are 1 1/4" long 1/4" wide. There are 7 windows that need the 3330P and two wind ... (cont.)

Top Sash Guide dimensions are around 15/16 in x 15/16 in on top part and 1 1/8" height. The metal stopper is about 1" I need about 14 sash guides and stoppers.

I need two 16" 1540 Block & Tackle window balances. I'm not sure but I think the bottom mount guide that attaches to the window may be broken as well. Any videos on how to know where the bottom window guide attaches is helpful. I have another rental where I fixed the window using your help suc ... (cont.)

28 inch 1/2 inch balance. stamp _ 2740 TN also 198 .The Bottom shoe i believe is 15-004 and top is 19-037 Glazing bead i think is 55-202-6 bronze let me know what you think also the rollyson top sash guide 18-118 looks like it would work also and the take out clip 16-002 ?

Need parts for windows: Balance rods - (2) 3375 ht and (2) 3375 jvstoppers (12)silver ?? (12)Have pictures, but do not see where to attachThank you,Mark

We are needing a couple window balancers. They are 26" length. Identifying number is 25-5 JI5 CMC 50. Also need window take out clips. Please supply parts numbers to order. If further information is needed please let me know. Thank you, Jeff