Viewing all customer Discussions for:

16-002 Take Out Clip

I am sending a picture of the latch. Its white plastic. Checking if you have them. Would prefer them in metal if possible. Could you advise the part number. I have purchased other hardware for the 351 series - forgot to purchase the latches that locks the windows from the inside. Thanks ... (cont.)

looking for the sash (block and tackle) for 34 by 28 vertical window. sash is 24 in long (metal to metal) and is 5/8"deep also looking for a few take out clips.

just trying to find the right part to order for 2 windows which is a set of four and also some take out clips there aluminum frame windows. any question here is my number jose

Hi, Please help me by telling me what I need to purchase/replace so that windows can be opened. Past homeowner left window channel balances off the windows so they could be closed. I looked at them. They have rust in the springs. I see the number 2730 on the sides. I see a two holes towards the mi ... (cont.)

I would like to order some take out clips that will work with my 25" Series 380 Channel Balances. thanks, Brad

Hello, I am looking into replacement balances and clips for my windows. I can not remove the balances as the clips seem to be broken and therefor I can not get the balances out. I am looking for help on replacement clips, so I can hopefully remove the balances and replace with new ones. If i ... (cont.)

I need 2 balance springs for an Alcan window. Also two take out clips. The sash is 32 inches high and 52 inches wide. I do not have the old balance springs for this window. Can you help me?

Need window parts identified so I can order parts. Sending more pics in 2nd post....

I have two problems with the channel balances on my Seal Craft windows. 1. Some of the balances do not stick with the window. They either stay in one place or move up and down the track some but not in sync with the window. Is there some way that they are supposed to click into the window it ... (cont.)

This is related to the below order. My contractor thinks I'm missing this part. Can you identify this for me? I ordered S38-31 Option 3030 and would like to know if there s any other hardware I would need to put this balance in its place? Please see attached for further review

I ordered some top sash stops that worked perfectly now my counter balance seem to have a problem. When I raise the window one side gets stuck see picture included. Notice bottom of window, counter balance is about 4 inches below window sash. Is this a counter balance assembly problem or window? Any ... (cont.)

Hi. I am trying to fix one of the windows next to my balcony door. It's apparently a custom size. The balance has the following stamped on it: (04/03) UNIQUE 55 E 32.25LBS. I measured the balance from end to end to be 56" and the spring mechanism from hook to hook is 29". The window weighs abou ... (cont.)

Hi I am replacing the top guides and spring/block and tackle hardware for (2) windows the actual window frame aluminum is 5/8 in cross-section, and the spring-channel part is 3/8"...I have included pictures but let me know if you need more... Thanks Rob

Do you have a video that explains how to replace a TAKE-OUT CLIP?

Please review the attached photos and please offer advisement on what I need to do with the pivot shoes and balances. Any suggestions is always appreciated. Thank you in advance for your time

I have 2 window balancers which I need to replace. The writing on them says 29 6 FBS (last letter BSI or RSI) I also need the clips. My clips loos a little different that the one shown. They are have a flat piece that clicks open, not the rounded looking piece (unless that is the back side). ... (cont.)

I need replacement balances for an Alcan. The number the existing balance is 2920 can you tell me what replacement I need? Sorry I don't have a picture to send.

Attached are photos of the existing sash balance which broke on my 24w x60L single hung aluminum window. We have been unable to get window removed to fully see part & don't want to until we have a replacement. We looked at our options & it seems to be closest to the 370 series 1/2 wide (9/16). We co ... (cont.)

House built 1981. Frame does not have balance stops. Stops appear to be plastic parts screwed to sash (window) Markings stamped on side 29 8 Need 10 pair

I do not have the original channel balance. Need help identifying the correct balance. I need left and right. I beleive the window is a Milgard because of the MM on the lock Thanks