Viewing all customer Discussions for:

82-005 Surface Mount Sliding Door Handle Assembly, 4-15/16"

I have an older house with a patio door that has screws set about 4 15/16 apart and what appears to be a non-keyed Mortise lock with a 45 degree lever. Photos of the disassembled set attached. The lever has bent and the door will not latch. Is the 82-080 the appropriate replacement? ... (cont.)

need a replacement handle both sides for my sliding glass door. the house was built in 1956

Hello, we're looking for a new patio door handle with lock key set. Thank you!

I have an Arcadia sliding door lock /handle that has stuck in the locked position. It has a button type latch system, you push the top square button to lock and bottom button to unlock. Is there a replacement available?

I'm looking to put a lock on our downstairs/basement sliding glass door as we can turn it into an AirBnB. The key would be on the outside. The attached pdf has the dimensions as well as I could measure them. Do you have something that would work? Right now we are renting out the upstairs, but we w ... (cont.)

I can't find any replacement locking sets with the exterior type lock seen in the attached photos. The stock set is non-keyed and only has an interior switch for locking (would prefer a similar replacement). The mounting screws are approx 4 inches on center apart

I have a sliding glass door and the handle broke off looking to order a new one I've ordered a few from stores and online none that fit,bottom glass door reads: trempe tempered CAN/CGSB-12-1M BS 6206-1981-A 16CFR1201 C11 ANSI 2-97.1-2009 1/BUA SGCC-1605 4012

Please see the attached photos so you can see what I'm working with here. The hole to hole measurements are 3-1/2".

My name is Jennifer. If it would be best to call me so I can make it short that would be best? I purchased my house a year ago, my neighbor has the same slider and it is from Pelllgem great lakes, but I do not know the make or model and the homeowner did not transfer the warranty. There is no sticke ... (cont.)

Hello There. I am hopeful you can help me identify some parts to 2 sliding doors that I have. I have one pill handle that is broken, another that is in tact. The outside handles of the 2 doors are old and I hope to replace them. I am not certain if I need a new lock latch, but that may also be need ... (cont.)

Replacement for sliding glass door handle set 7.3/16 x 4-15/16 centerThis is a very old set. The markings found on the handle are: PD9192M or pattent #99713 1976 or 4973 very hard to make out.Is the Swisco replacement set on the far left what I need along with the keyed side?I really appr ... (cont.)

I haven't been able to figure out which strike plate to order. It mounts to the face of the door frame but the hook type latch goes into the side. The screw holes are 3 1/2" apart on center. I need black. My door handle is 4 15/16".

Looking for replacement handles and locks (5 sets) for 1980 built home?can you help ? Thanks

The spring must be broken, the latch will not stay up, I want to purchase a new one, this is from AlenCo in Bryan Texas, there is no part number, and patent pending

I would like to replace the lock/handle on two older Peachtree sliding glass doors. I think the parts numbers I need are 82-005 and 82-306. Also would like both new locks to be keyed the same. DougPlease advise. The attached picture is the existing handle/locks

Hello, I am attempting to replace the handle and lock on this sliding glass door (see pictures of the door with it all removed). I have no idea who the manufacturer of the unit is nor do I have pictures of the old handle (unfortunately). The hole spacing for the handle mount looks to be about 4.5inc ... (cont.)

Photos from previous inquiry.

Canadian patent no. 919213 Patented 1973 PAT. NO. 3596954

I need to find the right replacement for the patio door handle attached photos. My existing handle set is about 5 7/8 inches from screw hole to screw hole.

We have a sliding glass patio door whose handle has broken. It is different in the sense that there is not a 'hook' but the door slides over a 'bayonet' screw that is attached to the door frame part of the door assy. I would need the handle as the attachment point for handle is entach. I don't wan ... (cont.)