Viewing all customer Discussions for:

82-106 Sliding Door Turning Lever

The slider that pushes up and down to lock my sliding glass door has broken. Attached are photos of the lock and a label that was on the door frame. Any chance you would have a replacement lock?

We lost the keys to our sliding patio door and am looking to replace the cylinder with new keys. Not sure of the door company, but the information on the door is:16CFR1201 CUANS1Z97.1 1984 1-8USCC-1100 401 1103Herculite KPictures of handle and lock are attached. From my measurements of the lock are; ... (cont.)

I'm looking for a different length post for this thumb latch for my padio porch door handle. What is the post normally called

I previously ordered a 45° Mortise latch but the slot where the locking latch goes in was too small. The locking latch is shown in IMG 0558.

I need the latch reciever that attaches to the inside of the frame for a Jeldwen vinyl sliding patio door.

I am also looking for the same thing LEGACY KEYED HANDLE SET, 3-15/16" (1-1/8" TO 2-1/2") Product Code: 82-086 work as the door handle ? it looks like the ones I already have. For the latch any help would go a long way. see below for a picture

Hello Please advise what part number to purchase to replace Dead Latch/Lock. Think it is Product Number 82-260. After attempting to adjust, will not latch properly.Lock handle appears to be loose..not sure If I have to replace that part as well.

Hi. I have 2 questions: 1st: Sliding door turning lever product # 82-106 is 13/16''long, would need about 1 1/4'', otherwise it doesn't reach the slot that turns the latch for mortise lock. Is this available? If not, do you sell extenders that I can insert? 2nd: Would need white exterior handle ... (cont.)

There are no identifying marks on the piece in question. I am trying to determine if the metal prong is bent or if it is supposed to be this way. It is twisted about 20 degrees off of the angle at the base. I tried to get a good view of this in the photo.

Hello,I'm looking to replace the handle on my slider door. The locking lever on the handle itself has broken. The mounting holes from center to center are 5 1/2". All the replacement ones I'm finding are less and I don't want to drill new ones. The locking mechanism itself is functional. The han ... (cont.)

Hello, the latch on my sliding door broke. Do you have a replacement part?

Need to replace lock mechanism for Crestline patio door. Dimensions: Bracket length = 150.25 mm Bracket width = 20 mm Hole centers = 140mm

We need a latch lever for a patio door. Lock works with a screwdriver. Door is1 3/4" thick, screws are 3 15/16" centers The latch is about 1 1/4" from the screw. It is not centered between screws. The key shaft from the outside of the door sticks through the door at about 7/8" leaving a gap of abou ... (cont.)

Looking for lock mechanism for 311/312 sgd slider See pic

I bought the 82-226 4 5/8" mortise lock and the 82-106 turning lever. However, before installing them, I found the existing door handle base added extra thickness that might prevent the lever from reaching the turning slot on the lock. Also, the hole on the existing handle doesn?t seem to be able to ... (cont.)

The knob to the lock fell offf. However the lock never really worked right.

I need the lever for an IWC slidding glass door in white.

Locking tongue is flopping in and out and does not catch the locking lip. I have used adjusting and screw and that does not solve problem. Is there a spring or cam that may be broken?

There is fixed handle on my Marvin slider 6' patio door. The lever behind it flips up to unlock the slider and flips down to lock the door. The lever must be broken because it just flops up and down easily with no resistance like it used to have.

The lock mechanisim is 10 inches long, 1/2 inch where the latches come out from (photo 3854) and one inch and a sixteenth deep (photo #3851). Photo #3851 also shows that it's slightly angled at each end of the mechanisim