Viewing all customer Discussions for:

82-302 Key Tumbler For 1" Thick Door

Reverse of exterior plate reads " JHL " and J302B2 Reverse of interior plate reads J302B2

I'm looking for a cam lock for an aluminum sliding door.

Do you have a key cylinder for 1-1/2" door thickness. (Similar to:Key Tumbler For 1" Thick Door) Product Code: 82-302

Looking for a keyed lock cylinder for this DNS pull that is 7.36 " long. Door is from about 1990. No numbers or markings on the lock. The pull is stamped DNS Industries, Miami, Fla 13/23 Outside Pull Standard The last picture is a lock set I bought but it is too small Thanks

We have PGT sliding glass doors that we'd like to be able to lock with a key on both the inside and outside. These doors are never used and don't want to take any chances with our little one getting outside where there is a pool. We have a normal swing door right next to the sliders, so no worries ... (cont.)

Does 82-085 come with lock cylinder or do we need to buy separately? If so, please confirm 82-302 is the correct matching cylinder. Thank you.

How exactly do I install a 82-302 key tumbler. Specifically, does the retaining clip pull out with pliers or depress into the cylinder allowing the cylinder to slide into place and then pop back out to retain cylinder in place. I ordered a 82-302 to replace my old one (with broken tailpiece)and pu ... (cont.)

I am looking to replace an old slider lock but the door is just shy of 1 1/4" thick so what is available in HD & Lowes does not work with the key lock as parts do not meet inside in center. Does this lock work in a door that thick?

Good morning,I am looking for a way to add a secure external key lock to the older door in the attached photos. Do you have parts that will accomplish this, or a kit I can install?Modification of the door will not be a problem, if necessary. Unfortunately there is no manufacturer (or any other) in ... (cont.)

I want to add keyed entry, and a grab pull bar, to the outside of my patio door. What do I need? The screws are 6-5/8"

I've noticed you carry the type of door tumbler that I need for my sliding door that is broken. Regards,

Will #82-302 lock work I have 1 inch thick door with a black handle on the outside, it has a knock out hole to install a lock However, the door has a mortise with 3 and 15/16 mounting holes and has a narrow rectangle hole at 45 degree 82-302 part has a round pin, a round pin will not fit into rectan ... (cont.)

Hello,Does this have another model for doors that are an additional 1/2 inch thicker?Is 82-302 available for a door that is 1 1/4" thick? If so, would it be compatible with the 82-002K set

Hi I need to replace a non-key door lock on a sliding glass patio door. 71/2" long & 1" thick frame. Black. I need the lock & catch on the frtame.

Park model slider lock set just pulled out of door with the key. What part do I need?

I need to replace a patio door inside pull. Stamped as DNS Industries 16 inside pull standard. Patio door locks and unlocks from inside only. Measurements match your 82-008. 7-3/8 X 15/16. Screw centers 6-5/8. But Your latch is facing down and my latch is facing up. Thanks Lydia

I have a DNS Industries 13/23 outside pull. The lock has the # 018 on it. The other side of the assembly has 16 inside pull. Is it possible to get a key or a lock with a keeper? Thank you for any assistance you can provide me.

Are these all keyed the same?

Dear Sir/Madam, I have a boat in England UK on the river.I know the boat came from lake michegan originally.The boat is a BAY HARBOR.i am trying to replace a door lock.On one half it has one half(the latch side,locked from inside the cabin) 12DNS industries miami fla,on the other hal ... (cont.)

The screws on handle measure 6 5/8" and were attached to the external keyed handle with black plastic mounts. the handle opening on the door is 7 1/4" high by 3/4" wide with the lock opening pretty low and 2" center hole. Notice the exterior handle, it sat on the outside of the opening edges and set ... (cont.)