Viewing all customer Discussions for:

82-310 Key Lock

Looking to secure this door by using a key to gain entrance. As you noticed there is no inner working. Looking for the handles - inside and outside, inner guts, With a key access to the outside and thumb lever on the inside.

My lock no longer locks or closes.. I need a door handle with lock.. looks like there was small bar n it broke off.. this is original to mobile home 1990.. can you help

I am trying to find a replacement handle for my sliding patio door. I am having no luck with the Imperial company. I have included pictures of the handles themselves and hardware from the door latches. Thanks you

Center distance of screws are 4"

Hi, I need to replace the lock on a BF Rich patio door. The handle and all hardware is fine. I just need to re-key the lock. Do you have a replacement lock?

Hello, I recently purchased a sliding glass door handle and 82-081 did not fit. The door is 1-1/4" thick, and the style is 2-1/4" wide. From the center of the top screw hole to the center of the bottom screw hole is 4-7/8". And I need a keyed set up.

HiI have already purchased 82-265 Multipoint Mortise lock with face plate 11"( Order No. 1920411)from your company. Now I need a matching lock for that 82-265 lock. I have attached a photo of the existing lock.Please advice. Bakhtiar

please let me know if you carry that part # too thanks

I'm looking for a replacement handle with lock for my Simonton sliding patio door .

I need a lock mortise for my door, and either a new handle assembly since I can't find the turn latch pin and/or lock bolt since it never came with keys

Key Entry, double teeth locking mechanism. Looking for a suitable replacement. Thank you!

The Patio Door is fairly new (Double Pane) and has a Vinyl Frame. All that I have is the Handle with a 3-7/8 Hole Pattern and the keeper plate that has a an overall length of 9-5/16 and width of 9/16. It has a double mortise hooks that are spaced 5" apart. In the door jam the Vinyl Strike Plate has ... (cont.)

I currently have the below and need a replacement set, the measurements from the center of screws on the inside handle is 3 15/16 and my outside handle has a cylinder lock and keys. Inside Handle has a part of 1060-1943 Outside has a mfg name of Sash Controls Inc, Part #1963.

We have a sliding patio vinyl door that we need to install a new locking handle with a Schlage keyway. the door is 1.5" thick and the screws are 3 15/16".Sincerely,Don

It looks like the part number of the handles are M0092A and M0091. Hoping you can find a Polaris handle or some other manufacturer that will fit the door.Thank you!John

Need a keyed lock handle got my Guardian Geneva slider door ANSI 297.1-2015 16 CFR 1301 II SGCC 2259 1/86A CAN/CGSB-12 1-2017

I have a white, vinyl Jeld-Wen vinyl sliding glass door that I purchased through Lowes (special order) about 12yrs. ago.... I need to replace the handle as the locking/latch part broke. It might be a SVC-90035? The handle has a center (vs an offset) latch. The handle is white, 8 inch long, 1inch wid ... (cont.)

Hello. I need a keyed lock for a American Craftsman 50 series sliding door. Please tell me what I need to do to order this. Door label and mortise handle with sliding lock photo attached. Thank you!

Hi There - I am trying to find a replacement handle for this IWC sliding door. This is the non-locking side which should be pretty basic but, I am having trouble locating this part. Can you help me figure out which part this is?

So the locking part of sliding glass door is broken. Any way you can help me out? I need the parts in the pictures and the locking part that fits inside the door. Please go easy on me.