Viewing all customer Discussions for:

82-310 Key Lock

I have a Certainteed Patio door handle, polished brass the broke at the screws.I don't need a PB one, a white one would be great.Here are some pictures of the existing and a postit of the dim.Thank you,Steve

I believe the two photos are from a Jeld-Wen sliding door. The single handle is the outside portion which pulled out of the bracket. The other photo shows two indoor handles. The one with the lock-set in the center between the two mounting holes is the original. The only new one I could find locally ... (cont.)

says it is an imperial USA door handle and it keeps bringing me to your site. The locking mechanism is fine just need the handle assembly. Thank you

I need a replacement for this door here are some pictures of the lock

My patio door handle is 7 1/2" tall by 1" wide and the lock is centered on the handle. It looks like your replacement part 82-086 would fit with the exception of the offset. From the picture on your webpage, it looks like the lock itself can be flipped around to be centered, but it doesn't appear th ... (cont.)

Hello, I'm looking to change the lock on a sliding glass door lock. The inside of the handle has DR05-1530 stamped on it. Is it possible to get just the lock portion/cylinder? And are they keyed differently? I'd hate to buy one and have it be keyed the same as I'm switching the lock for a new tenant ... (cont.)

This is an exterior door handle from the sliding glass door to an RV. It is plastic with 2 threaded metal inserts. The 5/8" diameter hole is for a lock cylinder. the inserts are spaced 3-15/16"

So does it matter if my handle does not extend out to 21/2"? Does that handle set include everything? Both handles, keys etc?

need full replacment with sc1 clyinder. screw holes on center on handle are 3 15/16s the single mortise hook is 5 3/8s screws on center.

Hello, Could you please advise what keyed handle set would be a good replacement for our patio door? I attached photos of the current handle set. From the center of the screws on the interior handle in image 1042 is 3 7/8". Please let me know what other information you would need to determine a goo ... (cont.)

I want to install a keyed door handle on my Pella patio door. I tried installing one from Amazon and the key cylinder did not work properly so I am trying a distributor (you) to assist me in making sure I am ordering the correct parts as well as trouble shooting the installation. ... (cont.)

I have a Wasco Rolling Patio Door, with #38739 stamped on the tag. The lock tumbler in my handle had broken, and I had replaced it with a generic lock tumbler at one point, which is very loose and finicky. I was looking to get a whole new door handle for it, as new tenants will be moving in soon. Ho ... (cont.)

Hi - I am looking to replace the lock on my sliding door since the key has gone missing. I'm assuming I'll have to replace the whole handle. There aren't any part numbers on the lock/handle, so I'm not sure what additional information I can give you. Thanks!

I am trying to replace an old handle/lock on a sliding glass door on a Park Model mobile home. The screw distance is about 3 7/8" apart. The mortise is completely missing. We do need a keyed on the outside model.

ihave patio door with amotise style door handle that will only lock from the inside i wont to get the parts to lock with a key from the outside . it has double latch system.

Locking mechanism is not working. Need to replace with keyed lock.

Hello. Would you please help me find the correct key cylinder for this door so I can replace the lock. I purchased the home and the keys were not provided. Thank you

I need to replace hardware on a KC sliding glass door. The existing hardware is shown in the photos below. I would like a full replacement of the handleset, mortise latch, and keeper. I would prefer to have a satin nickel finish if possible. I do not need to have such a tall handle. A shorter h ... (cont.)

I need a key lock on the outside please advise?

Hello. I would like to place a lock on this existing hardware. Is that possible? What would you suggest?