Viewing all customer Discussions for:

82-310 Key Lock

I purchased 82-042 and 82-310. Do you offer a spacer that goes between the handle and the door? I can't make a hole in the door to push the key lock drum inside. It's about a 3/16 thick space.

My door is manufactured by Kasson and Keller of Fonda NY. It has 1 1/2" wide door rails and the handle's mountig screws are 4" apart. The lock the company sent me would not fit inside the existing handle as molding inside the handle prevented the lock from nesting flush with the hole in the ha ... (cont.)

I have a Philips Products Series 870 Sliding Glass Door. The internal lock is broken. Would you have a replacement lock?The distance between the installation screw holes is 3 5/8 inches.

Will the 82 -310 work for a 1 1/2 wide arcadia door ?

I am trying to intall a good key lock on this sliding glass door for the back of my house so I can lock it from the outside. Its been tough to find.

Peachtree citation II sliding glass door cylinder lock/key cam . I am looking for a part number or replacement with a key.

Hello, I have recently followed instructions and installed the #82-310 key lock in my existing estimated 5yr old handle & mortise lock. It completely fits in my handle & mortise lock, no problems there. However, this new key lock seems to need to make a full turn to lock and/or unlock. But my m ... (cont.)

I have a Wenco sliding glass door. I believe it is a JX7 but i am not sure. it also has a number 52692 stamped inside it. The track has gone south on me and so I am looking to buy one of the track caps, probably the fuller or one as opposed to the little round one. Now I also want to replace ... (cont.)

Hi, The sliding door of our rented apartment has an exterior pull as pictured. We don't have the keys for it. We are looking for a replacement. How to select the correct door pull. Can you suggest any of your products.

My home has a Newcastle XT sliding patio door that was installed in 2002. The tailpiece on the key cylinder is broken off. I received no owner's manual or instructions of any kind when the home was built, and there are no names, numbers, or markings of any kind on the existing (original) key cylinde ... (cont.)

Howdy. I have a currently un-keyed Sash Industries PT. 1963 slider door handle set on my patio door. I would like to convert it to a keyed handle. The attached photos should help describe my setup. Would a Key Lock #82-310 be a good route to go? Also, is the 82-310 potentially able to be re-keyed by ... (cont.)

I have the 82-055K for a 1-1/8"-thick door, as recommended by our locksmith. Is the cylinder designed to be filed down to accommodate this width?

Hello I have a 2007 Philips Products sliding glass door on our newly purchased home. I need to replace the cylinder lock so I know it is re-keyed. What product of yours do I need to order. Or if their are multiple options; how do I determine which cylinder lock I need to order from you. ... (cont.)

How do I decide which keyed lock I need for my sliding glass door: 82-303 or 82-310? The handle looks like your 82-306? Thanks John

Would like to install keyed lock on the outside of of door.

The Key no longer go in easily and I have to force in, to the point that I no longer use the door to enter. Everything else works fine. Do I just need to replace the key plug and which one is the best.

Exterior and interior door pulls. Locking mechanism ok. Scott

My intention is to add a keyed lock to a sliding glass patio door. I removed the current handle/lock. The exterior handle says DOrWAL. The inside of the interior handle is stamped 120. My screw spacing is 3 15/16" and door thickness is 1.5" Can I just add a lock cylinder to the current hand ... (cont.)

I have a double mortise sliding glass patio door that came without a lock cylinder. I would like to add a lock cylinder to the existing handle. After doing a bit of research on your web site I think that your 82-310 lock cylinder might be the part I need. I have not yet taken the existing hand ... (cont.)

I am looking to replace the locking portions, or maybe the entire handle/lock, for this door handle. I do not know the manufacturer of the door (or the hardware), which is 1" thick. The door was installed in 2006, but the company that installed the door is clueless about replacing the hardware (wh ... (cont.)