Viewing all customer Discussions for:

S351-22 22" Series 351 Channel Balance

Hello I purchased 2 2130 sash and they are identical to the one that I had however this part does not fit with the sash my window will not go back in. Thank you

2130 w is the stamp code on the channel please point me to the correct product thank you

Please see attached photos of the window spring i need. I will need one set. number on the part is 21 12 BS1 R Thank you

I have a balance channel marked 21a and one that is marked 24b. What should I order?

I am looking to replace the balancers on several non tilt single hung sash windows, I have identified the stamp on the balance as follows, 2190 32; 22 inches long. After looking this up I see you recommend 22" series 351 channel balance, which after measuring the top guide and shoe is identical in ... (cont.)

I need to replace channels on two windows by Alenco one says 21 D and the other says 19D

Hi, On the channels, I found the markings, '21 4 JR Caldewell.' I measured the channels to be 1/2" by 22" (without accessories). I have a little trouble figuring out which accessories to put on the ends. I was hoping you can help me figure that out by attached picures. How much would it cost fo ... (cont.)

Balance has 21 12 on rail. Can't seem to submit photo???

Stamp option on existing is 2220B. Which option is best replacement for 22" Series 351 Channel Balance Product Code: S351-22. Thank you

I received the replacement part 22" Series 351 Channel Balance and installed it accordingly. However I noticed that the window sash doesn't close all the way unless forced down. I think this is due to the springs in the channel balance being too strong for the window sash weight. Would I need th ... (cont.)

Replacing two balances stamped 21 12 Window weighs about 28 lbs I was going to oeder your item number 22" Series 351 Channel Balance Product Code: S351-22 using the 2150 weight range but am unclear if i should be dividing the weight by 2 since each balance would be carrying half the window weig ... (cont.)

why not get a 2140 instead of a 2130 , for the sash weight ?

I need to order some 351 series window channel balances. I don't have the balances to get the part numbers from however I do have the height of the window panes and their approx weight . 2 pcs. for a 21" tall pane 10 lbs. ,4 pcs. for a 24" pane 15 lbs.,4 pcs for a 16" pane 10 lbs. ,2pcs for a 10" ... (cont.)

Can I order S351-22 with 15-001 shoe attack and top with 19 002

I have a window without balances and need to know how to measure the sash to order the correct length. I ordered 28" series 351 block and tackle for another window and it was fine but this window is shorter and I am not sure how to measure the sash. It is missing it's balances all together, so no i ... (cont.)

I am looking at the S351-22 and the S390-22 Channel balances. My balances have a similar shoe to the 15-001 except the 1 1/8 dimension on my part is 1 1/16. Does the actual part meet the 1 1/8 dimension or is it slightly under and closer to the 1 1/16 I am looking for? If not I will order the S35 ... (cont.)

I have measured the channel = 1/2 I believe I have identified top = 19-002 I believe I have identified bottom = 15-002 Measured length as per illustration = 22" My Balance has a 21 12 BSI stamped on it. It doesn't match any of your listings. What should I be ordering? I will need four ... (cont.)

non tilt sash S351-22 flow balancer.stamp no balancer is 21-12 BSI.Sash weight is 50# ?. what option do I need for correct spring? thanks Mark,

The model number on the channel Balance is 2120. Based on the measurements I took, in order to replace the entire mechanism I would need part "22" Series 351 Channel Balance". But before ordering 8 of these I would like your concurrence based on the pictures I took. Thanks.

re; S351-22, re; stamp ,you have options from 2110 to 2150 my stamp says 2190 32 do you have this model dave thanks