Viewing all customer Discussions for:

S380-30 30" Series 380 Channel Balance

I need 2 balancers.Window is 64h x 40w Milguard. Sash weighs 25lbs. Balancer is 30 in long.

The stamped letters/numbers are 29 4 DX CMC 7

Looking for milguard balance Pic is of numbers on part and numbers on window.

Looking for these tracks. Need to replace ours they are old and windows are getting stuck. Would u have them in stock

I Need two balances, a couple of little square track guides, and a couple of the arched springs that go in the locking lifters (if that makes any sense.

Hi Swisco, Can you help me in find the correct window channel and take-out clip. My window channel has the number of 29-3-HV-CMC-7 marked on it. The lenght of the metal rod is 30 inches. The take-out clip is 1.25 inches. The metal rod thickness is about 9/16 of an inch. Thank you. I would nee ... (cont.)

Hi Swisco, I need balance replacement channels for 12 non-tilt windows. 1. 29" (4 windows) 2. 32" (8 windows)

Need to replace the 2 balance springs for bottom sash. Bottom sash weighs an estimated 40 lbs. Balance spring is 30". Markings on spring are 29 5 HV CMC 2. My phone # is 812-629-8806 Thank you, Mark

The Channel Balance Assembly is 1/2" wide x 30"long. It is similar to S380 except bottom shoe depth is 7/8". Top guide and bottom shoe are both winged. The top guide appears to be 19-005. The bottom shoe appears to be 15-029. The assembly is stamped "2920". Is this assembly a stocked item or a speci ... (cont.)

All, I'm having a hard time figuring out which part I need. Most of the windows that I have are of the same dimension. I took out one sash and weighed it on a scale which came out at around 17.6 pounds. I located a stamp on the block and tackle which was 930. Measured the length which verified at 30 ... (cont.)

I have a Balance rod with odd stamps on it. Odd to me anyway. It is stamped 29DS 48L. Now I'm assuming that its a 29 series, double spring? But I don't see a double spring in it, just 1. Amd a sash weight of 48lbs. I wanted to verify all of this. Plus I don't see double spring balances on your sight ... (cont.)

Picture of 30 inch channel balance and top sash guide. They are lawson window from 2005.window size 30 x 51 weight 38 to 39 lbs. And other window is 36 x 34 weight 28 to 29 lbs.

Hello, I need custom balance rods to replace original rods as follows: S380 35" with 15-029 shoe replacing 3435 original rods. I think 3440 will do since you do not seem to have half sizes on window weight. I need 8 of these. S380 23" with 15-029 shoe replacing 2220 original rods. I need 2 of ... (cont.)

Need help identifying this part.

Hello, can you please help identify which balance I need. The measurement is 30in. The print on the metal looks like 29-9.

I have one that is operable and the other one is broken. I would like to make sure I am ordering the right part. Any help would be appreciated. It is printed with 2930 But I am not sure if I need a 5/8 inch or half inch guide. Thank you for your help

Windows balances 29-5 dh5 cmc 75

Hi there. I'm in need of the following parts for my windows. The only other information I have is that it is a 2930. Any additional help you are able to provide is greatly appreciated.

I need to replace this Do you have these The metal is 30" long 9/16" deep 11/32" wide

Channel is 30". I'm thinking series 385 30". Just need to verify. Thanks.