Viewing all customer Discussions for:

S380-30 30" Series 380 Channel Balance

It was stamped with 29 3 JW CMC 11, would you know the equivalent replacement? It seems the 380 with 15004, I assume those are pre assembled with 15005, are those easy to replace?

Hello I have aluminum single hung windows made by milguard on or about 1990 channel length 30" " Width .50" series 380 the stamp reads 29 9 ET CMC 2 I need to know the weight rating

I have matched the dimensions of all of the parts of my channel to your 30" Series 380 Channel Balance, but I need help figuring out which stamp option to choose. As best as I can make it out, the stamp on my existing part reads 29 - 3 EBS1 Thanks for your help!

Hello, I installed the counterbalance and top sash guides with no problems except the window slides down about 50% , I double checked the original CB stamp and it says "30" so my guess is the springs are of a wrong weight. ??? Please advise . Thank You , Mike

It appears to me by looking at your examples that I need a 30" series 380 w/option 2940 (#stamped on my balance). The problem is the shoe. The 1/2" demension is fine but the other one is not an inch it is 7/8". Will this be a problem?

I order balance 380, for some of my windows am thinking the side part thst is attached to window is bad where the window will not stay up

Enclosed find diagram and pictures of sash top I need. Six are needed. I used your balances S380-30 series 380. The new balances worked fine. Great company! Gerard

I am not sure of what type of windows but have multiple windows with the same problem. The top sash guides all BREAK making the channel balances not work correctly. I have taken 3 windows out and there are also 3 channel balances that seem to be not working as well since the pulleys or rope are all ... (cont.)

Hi there, I have several windows in my Florida home that have broken due to the top sash guide breaking allowing the balance to move from the jamb. The pictures show the markings: 29 S (or 9?) CW (or GW?) CMC 11. They are 30" long. I think I have identified the correct part from your website, but w ... (cont.)

Hi. I am trying to identify which series this channel balance is from so I can order the correct parts. Thanks

Hello, so after about 3 hours of trying to figure out what parts just broke on my sliding glass window, I have decided they were called top sash guides (the plastic part connected to the sash that the channel balance is held into place with). I am assuming they broke due to sun/age/etc, so I found y ... (cont.)

I need a 2990 stamp option channel balance. Quantity 1 30" x 9/16" (1/2")

My channels don't match your models exactly could you tell me which would work for me. All my channels are marked BSI 2910, 2930.

Hello, I would like to order a pair of channel balances for a Milgard window, but I

The window is a single hung PGT window 52 X 61 3/8 The Metal on the channel measures 1/2" width / 30" length Nymber stamped on channel is: 29 9 (then smaller letters BS1 RV) Can you please advise the proper channel kit to get to repair this window. Thank you.

these shots are from a twenty year old Alcan window. The balance is 30"x1/2" the markings read 2920 B.S.I. HC do you have a replacement that will work? Thank You, Robert

I need to purchas 4 of these window channel balences

I am replacing the channel balances on a non-tilt window for a customer. I have determined that I need the Series 380. The channel balance is 30 inches long. The channel balance has a code stamped on it 29-6 GA2 CMC 5. Can I determine the weight of the window with this number or do I need to make ... (cont.)

I am trying to locate a side load channel balance that is identified with p/n 29-9 AA CMC 11

I need to replace several 30 inch window balances. 5/8" wide, 5/8 " deep. Plastic ends are broken per photos. I believe your 30" series 385 channel balance, prod code S385-30 will work for me. Am I correct? Do you need overall window measurements? Thanks so much for your help. Loleita ... (cont.)