Viewing all customer Discussions for:

S380-30 30" Series 380 Channel Balance

Please do me a favor and view the attached images and email back with suggested part numbers i am speculating they are the 380 series & email me back with conclusion asap thank you so much this ain't the rirst time i use your company to place an order you all did an awesome job getting me the right ... (cont.)

The balance has writing that is not too clear in the picture, but says: 29 9 HW CMC 11. There are no numbers I can see on the end pieces ( I need 2 of them for the top left and right of the window. For the latch, I did not take a picture of the broken one, but a picture off the adjacent window. I ... (cont.)

I spoke to someone in your sales department earlier today about problems with the balances on a Kinco window and was instructed to send photos of the number stamped on the track and the top and bottom of each end. The photos are attached, although the number does not show up well. The number is 29 ... (cont.)

Hi. I need two 1/2" window channel balances 30" long. Please see the attached pictures. There is no part number on the balances and other than the information below there is no manufacturers name on the Windows. There are two stickers on the window. One says Series Mark40/50 SH W.B., AAMA /NWDA ... (cont.)

The part is marked with 29 4. The clip at the top is broken. I need to order the correct part.

My name is Norma Martinez and I need to order 6 balances for my windows. I have attached 3 photos. I believe the measurement of the balance is 30 inches in length. Please let me know if you carry the part and what is the cost. Please contact me as soon as possible as I need to receive the parts ... (cont.)

2940 BSI

This is 30" in length 1/2" wide. I have attached the pictures here. Please let me know what exactly I should order

I have 4 Nuair windows where the window channels have failed. I have attached photos. The winows are single hung, the movable sash is apprx. 50" W X 31" T and using a bathroom scale they weigh about 24lbs. We bought the home new, and these 4 windows never worked smoothly, the balance springs always ... (cont.)

Hi I need to order 4 channel balances and need help identifying which ones to order. They are 30 inch x 9/16 stamped with 2940. I am attaching photos to help identify. Thanks!

30" Series 380 Channel Balance Product Code: S380-30 Not certain as to the strength of the spring. On the old channel balance there is a code of "29C USB" That is the only information I can locate on the metal arm. Visually all other aspects match up to your diagram on line. I will be pur ... (cont.)

Need correct part number

I have a broken channel balance & when searching through your site my model # 29DS38 does not show? My sash weights about 39 pounds & I have included pictures. Do you have a suitable replacement? Thanks PS The top plastic guide that screws into the window also needs replacing. PPS: I am sending ... (cont.)

# 2950 Window spring balances and plastic keeper caps

One of my window balances broke and based off your sites recommendation, I will order two, however I'm not entirely sure which to get since my stamp doesn't match anything on your site. The stamp reads "29-9 BA CMC 11". Doing some measuring and best guessing, I'd say it's your 30" Series 380 Channe ... (cont.)

I recently ordered S380-30 : 30" Series 380 Channel Balance. While replacing the balance however I noticed that the top sash is also broken. I looked through the website but couldn't find any top sash that has two holes. Attached is the photo

I got a 2006 built home with Kinco Inc (Jacksonville, FL) windows. The balance bars need to be replaced as well as some of the plastics caps on the window and frame. These are the measurements and incomplete reference of the existing windows: Length 30" x width 1/2 in. The reference starts with 2 ... (cont.)

I'm attempting to repair several windows. I am unsure how to correctly identify the caps or whether to replace the entire tension bar.

Greetings, I have a Harcar window that needs new channel balances. It is marked only with "29C Z" on the sideplate of the old balance. I have seen this marked as FA-2930 on other websites, but would need to end pieces (plastic clips) to make it complete. Would you need photos? Thanks ... (cont.)

Measurements Long 30in (metal part) Wdth 1/2in (see picture) Marks/numbers. 2920 D BSI