Viewing all customer Discussions for:

S380-33 33" Series 380 Channel Balance

Hello! I am looking for assistance on identifying the channel balances. Attached are photos. The overall length is 33". The width of the balance shoe is 1 1/8" The identification is different between the two. Not sure why. One side is 32 4 ER Caldwell. The other side is 32 9 KQ Caldwell. Thank y ... (cont.)

new part

Hello, Can you please direct me to the correct part number for my Milgard window balancer. I will need 2. Numbers on the balancer is 32 4 DV CMC 7 Thank you.

I am looking for 2 complete channel balances for my non-tilt Millguard window. The sliding window weighs between 25-30 lbs. I have included pictures of the channel balance I removed from the window. I question if it was the right balance to begin with as it may have been replaced before. I measured ... (cont.)

Hello, I have this window spring and the end looks slightly different than what is shown on your website. I'm know you can direct me to the correct part to purchase. Thank you, Kyle

My window balances have the markings caldwell 32 4 FQ. I need 10 which balances do I needs I also have a 26 4 AQ as well. Thank you

Replacing the balances in single hung vinyl windows. original part is 33 inches long (not including plastic end pieces), 9/16 inch wide, and 5/8 inch deep. Stamped markings on part are 3230 BSI.

I have Milgard windows. I have 2 window channel balances that are broken. One is 33 inches long and stamped 32-4. It is 5/8 depth and 1/2 inch width. It has winged upper and lower parts. The other one is marked 26-5. It is 5/8 depth and 1/2 wide. It has a lower winged and I suspect upper winge ... (cont.)

Attached are photo of the parts that we need: Qty (4) 3250 balancers (metal length is 32 7/8" width is 5/8" Qty (4) 2640 balancers (metal length is 26 7/8" width is 5/8" Qty (10) sash shoes Qty (2) steel clips used to hold the balancers in place during installation. Please let us if ... (cont.)

Hello, just looking to make sure we order the correct replacement parts. Thank you

Questions: I need to replace the push-pull window tracker with stamp 3250, the channel length is 33", the track also have another number 32 5 BM CMC 32 5 FU CMC 2 32 9 CW CMC What are those number 32 5 xx yy mean. so, which one is the correct replacement part.

channel length : 33 inches long Stamp on metal: 32 3 JN Caldwell Sash height 34 1/4" , Width 32 5/8" Sash weight 22 LBS need 2 balances and 2 window mounts(see photo)

Hello, Can you please help me find the correct window channel balancer to order. The balancer I have is a non-tilt channel balancer, measures 33 inches (just the silver part) in length and 1/2 inch width. There is a 32-4 stamped on the window balancer. I have attached pictures and please let me kn ... (cont.)

I am trying to figure out exactly which channel balance I need to replace this one that no longer works. The stamp is 3230 and then has BSI and OJ on the stamp.

I need to replace two channel balancers for one window. Does the number 32 indicate that the metal part is 32 inches long? Any additional help that you can provide to assist me in getting the correct balance would be appreciated.

I have a 22lb Milgard window & I need to replace both balancers. The balancer has the marking, "32 4 BX CMC 7" The balancer is 33" long

I have a non-tilt, milgard window & need to replace both balancers. The window weighs 30 lbs. The balancer is 1/2" wide & 33" long. The stamp on the front: 32 5 CX CMC 11

Printed as "32 4 EV CMC 7" 33" in length.

Hi, I'm looking to replace this window channel and replace the broken cord on another one. Can you please advise which part are needed. Thanks

Need to replace both channel balances on a Milguard window. Channel length (excluding fittings) is 33" Shoe depth is 1-1/16 inches Marking on channel is 32 3 DU CMC 2