Viewing all customer Discussions for:

21-155 1/4" Push Nut

We have 3 bi fold doors that need repair and one double bifold door that needs repair.They all need new stationary pins, plus the pins with the springs. the double bifold door keeps opening off the track, not sure if it piece that runs across the track is too short.Do we need two pins for each stati ... (cont.)

Hello- I would like to replace the hardware on my Fenestra metal closet doors. I have enclosed the pictures, which I hope demonstrate the proper dimensions. Unfortunately, I purchased 21-001, 21-007, 21-154, which are for a similar door, but do not fit mine. I was hoping you could point me to the c ... (cont.)

Hi! Wasn't sure, I just couldn't find this size on your site so wanted to ask for help! This is for a mobile home bifold door system. Any help would be greatly appreciated! Thank you, Liz

I am renovating my place and decided to spray paint my old closet doors, unfortunately once I removed the doors the top pivots came off and the little plastic plugs are no longer keep them from springing out. I will need to order new top pivots and bottom pivots along with additional stationary pivo ... (cont.)

STRATO-TRACK INC. is stamped on horizontal bracing. Tracks are fine.

I have two sets of metal bifold doors that are old and don't work well. They don't stay in their nylon clips, are hard to open and shut, etc. I think the tracks are still okay, so I want to get all new pins, springs, nuts, and nylon clips for top and bottom rails (I assume you can replace those by r ... (cont.)

Need 9 upper & lower guide pins and bushings, 4 top pivot pins and springs if required, and 3 adjustment (lower pivot) pins. See parts drawing photo for nomenclature. I need parts for a home sale asap!

We put in new metal pivot rods in our bifold doors, is there any way to level the rod up and down, the bottom left rod needs to be lower st stay in the guide hole....HELP

I recently purchased a house that was built in 1974 and it has the old metal bifold closet doors that 36? and on 72 inch guide top and bottom i need bifold kit for pivot top and bottom

HelloI moved into a condo with metal closet doors. One door is off the track and someone has tried to fix in the past. I think they are from the 70s. I hope I don't have to replace the tracks top and bottom. Photos are of parts that appear to be in need of replacement. I don't see any numbers or mar ... (cont.)

my pins or the ones i am looking for are about 5.25 long with a .250 shaft with a groove for a hair pin clip and the cap on the top is about .410

The top guide wheel is not able to stay up seem to be missing an nylinder and bottom guide wheel is Bent Ned a replacement part Steel Full-Vu Door Leigh Products, Inc.

CAn I use part # 21-007 21-001 21-155 To replace in the photo attached

I am trying to locate this guide pin. They are original metal bifold closet doors were installed sometime in the 1970's. the two side grooves broke off the original. Please let me know if you have them and where I can get them. Thank you Debbie

I need both a top and bottom guide post assemblies for a National door which uses your part no. 21-113 guide on my track. Please include springs, clips and installation diagrams. Joseph W.

Hi there. Looking for a replacement of the bottom pin on the old bifold metal door. What I know is that it is 5.5 in long and 1/4 in diameter. This is the original door that was installed by the builder sometime in early 60th. Any suggestions you can provide on the type of the pin to use would be gr ... (cont.)

I am attaching the photos of my metallic closet bi fold door's hardware. Top pivot : refer top pivotphotos 5 inch long, 1/4" dia with a plastic washer or cap to hold the pin top and bottom of frame (on a door- See photo top- 8) And a two metal push nuts with cuts to hold the pin( photo no (1,2 ... (cont.)

I need four outside pivot rods with spring I believe . The inside pivots are in good condition..this is 2 -36" bifolds ... Can u find the correct outside pivots for these doors, they are missing, thank u

We need to purchase complete mounting hardware minus top and bottom track for 10 doors. Doors were manufactured around 1970. Thank you Jim

My appartment complex has about 300 leigh doors, all it says on the doors is quality control approval number 559245 I need hardware kits for the pins and the bushings that slide in the rails both top and bottom