Viewing all customer Discussions for:

21-401 Bifold Track, 3' Opening

Looking for 0ne set. Left and right . Must be identical to photos. Each piece is 36". Thank you.

I am in need of some parts for half of a 1960's era bi-fold metal door. The track is 3' long !1/16 x 3/8. Not opposed to using the 5/8 track you have if it works based on these pin. Looks like I need replacement pins as well. Thank you for any information. Bruce

I'm replacing my hollow wood bi-fold doors with metal bifold doors. I looked at the replacement hardware I would need from your thread with similar metal bifold doors. My question is, will I also need to replace my track, or can I purchase a wheel cap that will work with my existing track? Here are ... (cont.)

Can you tell me which track I should try to replace on my 1970's Metal Bi-Fold Closet Doors? I can't tell from the pictures if I need 21-401 or 21-452. Attached in my pictures are the doors, the track and hardware off one side of the doors.

I'm not able to tell what track I should purchase for my metal bi-fold doors. My doors are from the early to mid 70's. Our whole house has them but the one in the family room was replaced with wooden 6 panels (junk). The previous owner left the old doors in the basement thankfully. I am able to fin ... (cont.)

Hello - we are looking for a replacement of the bottom left track for the pictured closet doors. Is the part still available and can one of the two pieces needed be purchased to replace the broken piece.

What do I need to make this bi-fold door work smoothly?It scrapes and is difficult to open and close.Thank you very much.MikeI will send pictures of track also. Perhaps that needs replacing too.

I received bottom track for my metal bifold door, 21-401. Note 2 photos. I think you refer to the pieces as floater and pivot ? Your track is less wide as my old one. My floater piece (under the spring) is wider than the opening on the track and does not go in.I want to order the 2 parts (floate ... (cont.)

Hi! I need your help identifying which parts I need. I have three set of these doors. One on 36 inch tracks and two on 59 inch tracks. I would like to recondition these doors so they open and close nicely. Somebody at swisco showed me the 21-044. The the closest if not the se vracket would ... (cont.)

Nylon missing on guidance track pin. Door catches unexpectedly while closing/opening

We are trying to install a set of used doors that are 36 inches wide and we need to have the tracks that will fit the three eights inch pin on the doors

I would like to get all new tracks and hardware that sits inside the tracks for my 48" metal bifold closet doors. I have 5/16 inch pins and plan to reuse those. Can you take a look at the attached photos and let me know what you recommend? The bottom track is 1 1/8 inch wide measured from the out ... (cont.)

Hi. Bought the home . No clue of manufacturer or when they were put in. No one seems to know 1. How to replace or 2. Where to get the parts. Gosh, I hope you can help! There are a bunch of these in the house so I assume will happen again. (The top one had a plastic cap.) Pix below. Thank you for you ... (cont.)

Bottom connector to the guide in the floor. The top of the long rod has a slot to adjust the height of the door with a straight screw driver. No manufacturer's name o Rd number is available. The door is about 26 years old.

How can I hang this type of door without putting a track on my vinyl floors? What is the part number for the Pin with the spring at the top of the door?

I need the top tracks and pins for the bi-fold doors in the pictures below,are these available? This house was built in 1957 and these are the original floor to ceiling closet doors

Hi friends,We are facing difficult times with our metal doors in two of our buildings. We are a non profit housing organization called MTR - More Than a Roof Housing Society and we wanna replace our tracks and pins (not the metal doors) by new ones, probably different ones... Today we use parts like ... (cont.)

We have a mirrored slimfold model E door going into a small walk-in closet. The bottom inside pin constantly shifts in toward the closet edge, making it nearly impossible to get the door opened or closed. Not sure what parts we need. Am reasonably sure we need new bottom pivot pin and possibly ... (cont.)

Hi I have bi-fold metal doors, 3 feet (1 door), 5 feet (2 doors) and 30 inches (1 door). I am going to replace all the pins and tracks with your help (of-course). Can you tell me the parts needed. Thanks P.S. I researched on SWISCO.COM and I placed an order (1139482) based on what the parts for on ... (cont.)

I have an old Leigh Metal Bifold door that needs a new bottom track, cap and bumper. Approximate measurements for the existing track are: Length 3' Width 1" Height 15/16". Would your Part 21-401 track be an acceptable replacement and what other parts would I need to finish the set up for the new tra ... (cont.)