Viewing all customer Discussions for:

S770-27 27" Series 770 Balance

It's one is 27 " and other one is 29 "I think the width is 8 cm. Thank you for your response.

These balancers are from 2 different windows. Both are tilt windows and the balancers are 1/2" wide. They both have the same ends as pictured. So, I need 2 of the C2745s, and 2 of the C3920 (52)s. Please let me know if you have further questions. Thanks, Jimmy

I have "Milestone" tilt windows. I have replace the channel supports with S770-27 balancers. I need pivot shoes 1/2" x 1" wide. It seems all the pivot shoes are 1 1/4" wide. What do you suggest?

Please assist in hardware that can be seen in the attached photos. Thank you in advance for your time.

I need to replace a channel balance that measures 27 inches and 1/2 inch wide. The stamp on the balance is C2745. Thank you

The actual measure of the channel is 35 " 9/16" wide by 1/2"deep actual measurements. The stamp says Unique 34-C-30. I need at least 14 of these. I need 14 of these. The others are stamped 26-D-40. I need 10. The end clip is different than you off on this model please advise.

From single hung tilt window, circa 1995/96. No maker markings, channel counter pull has markings of "J C2730" or "K C2735" depending on window (which I presume are 27C 770 series channel pulls). Uncertain of how thick they are -- there are four nubs or raised spots on front of slide. If you don' ... (cont.)

Hi The balance springs on several of my windows have broken. the stamped writing on the back of the channel says " Unique 27-0-40. Which one of your 770 series will match. Also I want to remove two of the non-opening windows directly above the tilting windows. Is there a simple method to achieve t ... (cont.)

This is a channell for a double hung tilt out window. The channel measures 27" It screws to attach to the top and has a small metal clip at the bottom of the string to attach to the window gluide. There is a block and tackle inside.

Please let me know if you have replacement parts to match these items? Thank you, CMV

Hello, I have a double hung wind where the outside balancers have had the pulley to spring interface break. I originally looked up and ordered 770 x 27" based on the fact that the channel is not ribbed. Now I see that the balancers I have are 751 but not ribbed. Channels I have: Markings ... (cont.)

Need to replace a broken Channel Balance. Your series 770 seems to be the proper replacement. Markings on the existing balance indicate Unique Balance 27E from 2004 as shown on the attached picture. The balance actually measures 28 inches but the marking on it is 27 E. Do I order a 27 or 28 inc ... (cont.)

a tilt shoe of my window which is installed by champion window in 2006 is broken and I don't know the part number and the series number . do you have this part or could you please provide the part number. thank you .

My existing channel balance matches the series 770. My question is the overall length of the channel balance is 27 inches. On my existing channel balance its stamped with 26C. Which one do I order?

In need of 2 ea. Unique 27-E-50 & 27-F-60, unless you can suggest a better fit. Both sashes are the same dimension. 50"w x31"h. Overall length of metal balance is 28" Swivel clips are 1"wide x 2" long. I would think that both windows being the same manufacturer & the lower sash being the ... (cont.)

Hello, I have a window that has a busted Unique 27-D-40 balance. In looking through your products, the 770 Series 27" D appears to be an exact match (see pictures of my balance). However, my balance did not have a spacer at the attachment point and the set screw is all mangled as you can see. ... (cont.)

I have 2 different windows weights and need to know if I need different parts for the heaver windows. The broken part number in the photo 12:10:58 09/23/04 Unique Balance 27F All of the broken balance measures 28" long with the U shaped channel 1/2" X 1/2" There are two windows sizes with diff ... (cont.)

We have failing block and tackle balances in 3 windows and I think I've found the ones we need on your website. However, I know VERY little about windows and have a question: we have single hung windows, a block and tackle balance on each side so do we have to replace both balances in the failing wi ... (cont.)

See attached photos for markings, 27" length (of metal portion) 9/16 by 9/16 27D HC5 CMC 45

I have a 28 in balancer "Unique Balance 27F 12:10:58`