Viewing all customer Discussions for:

39-286 Casement Window Handle, fits Andersen

This operator is from an Andersen window. It looks like it's from the 60s. -- The arms are approx 11 1/4" long -- The track is 27" long -- Fully extended (closed position), the arms measure 25 1/4" long, from the end of one to the end of the other (not counting the shoes) -- The screws that remain ... (cont.)

The house I bought was built in 1960. About 1/2 of the window opneners do not work. Some just missing handles other's if you crank, they just spin. The beveled gears are stripped. The arms are over 12 inches and clip into a rail on the bottom of the window. These windows open out like an awning. Th ... (cont.)

, I have a window the same size as this one that opens on the opposite side. That is the one that I will need the hardware for. It's currently not opening, so I can't get the numbers from it, but I know that the mechanism is stripped and it needs a new one. The numbers on the crank arm are shown in ... (cont.)

I sent an wmail w specs. Please help

Need the crank and whole component for Anderson window. Arms measure approx 9 inches out, then 3 3/4 inch arms and the one 13 inch arm that connects the arms.

Have 2001 vintage Andersen casements. 31 1/2 x 60 19 3/4 x 60 Operators and hinges are bad. Appear to be straight arm (windows are rusted shut).

Hi,Do you carry a replacement seal for this window? It is an older Anderson wood frame double hung window.Separately, also looking for a replacement crank for a different, but also older, Anderson case window. It opens to the left. Part No. 39-147 looks like it might be the right fit, but is ther ... (cont.)

I need help identifying this window crank.

Lettering on arm says Anderson Windowallsreverse has stock no. 7198-17Picture Window crank 1 shows sharp edge where it may have been broken off

Good afternoon, I am hoping you can find this casement window crank handle. It is terra-tone color. Thank you in advance for any assistance you can provide. Thank you, Andrew

I have an old awning window that needs a replacement for the crank opener. I removed the old one and was told at my local hardware/lumber store that the replacement would be $232 plus the handle. They were able to find the replacement piece. The only markings on the device is the # 122 on the upper ... (cont.)

I'm restoring a house from 1957. It has about 25 windows like this, very few of them still operate, Can they be replaced or restored?

I need the attached crank mechanism. Can you tell what I need from the pics? thanks

This is the crank for a casement window. The serial number on the crank is 60-C-7041-62. The splines on the inside of the crank are stripped but the splines on the corresponding part are good. The window will open when the splined part on the gear box are turned by hand.

Looking for a left sided window crank replacement for Anderson casement window. The crank on the right has CX4-CX5 on it. The crank arm measures approx 111/2 inches

1. Window crankbox is completely cracked and handle is missing 2 . screen is completely missing. I know Anderson has a clip that is "integrated" in their screen, but is there an alternate clip that I could use that would work in this slot (with a generic screen)?

Do you have Anderson Roto Operator part number 0333908 and handle 0536011...this is for an awning window vintage 1973...if so please provide pricing and lead time...I need 2 of each..Here is a pic...15" to center of pin fr bend in arm ... also note it is 4-1/8 hole center dim.... thanks... this wind ... (cont.)

I am not looking for the shoe but I need to replace the metal rod that goes through the shoe as it is rusted.

A. Photos show a LEFT hand operator (I'll probably need a RIGHT hand, also).B. Note the tip "glide" point on the arm is a "DISC'", not the more common rectangular "SHOE".C. No other markings or identifiers on the window frame, glass, etc. (really? couldn't stamp a Model# next to your company name ... (cont.)

I have a few windows where the operator is not working well or the inside is stripped so it won't crank. I need the operator and also the crank but have no idea what kind it is or what I can use to replace it. Thanks, Chad