Viewing all customer Discussions for:

26-366 Vinyl Window Sash Pivot Bar

Good afternoon. So I recently ordered some pivot bars from you guys. #26-366 and everything is exactly the same as my old one except the tongue part that goes into the shoe is longer by a 1\4. I didn't realize this till I took apart a window that didnt have the bar broke and seen that it was a littl ... (cont.)

Markings: Series: Twinseal Single Hung H-R25-46x77 H-R50*-35x61 (MODIF) H-R50*-32x74 (MODIF) I wanted to confirm my selections: 26-200 screw plug 26-366 pivot bar 26" series 795 channel balance Thank you

What series would I purchase to replace these block and tackle? The sash were stuck and my customer broke the vinyl around the pivot pin trying to lift them. I'll deal with that later.

I'm having trouble finding replacement pivot bar, would greatly appreciate your help. Looks like S795-29B Channel Balance would replace my broken channel balance but now I need help with pviot bar. Dimension wise, 26-336 is very close, but would it work? Hal

Looking for a replacement

I have a Milgard window Installed approx. 2000, Single Hung, Bottom tilt out, w/internal grid. Width is 25 13/16" clear glass. The Right and Left hand Balancers no longer work and am looking for replacements. There are 6 Milgard windows in the house and only one has this problem. All 6 have the rou ... (cont.)

I need replacement balances for the double window pictured above. Please provide me a list of part numbers, quantities, and pricing so I can place an order to repair both sides of both windows. Parts will be shipped to area code 29316. Any other important information that you can provide will be ap ... (cont.)

I am looking for a replacement for the block and tackle sash lifter shown in the pictures. The windows are approx. 20 yrs old and the sash is ~18 lbs. I will need a right and left side if they are handed. I will also need replacements for the pins that go in the bottom of the sash. Thank you fo ... (cont.)

overall length is 3 1/16" tip is 9/16" Thank You

I need to find a compatible pivot bar for my single-hung, tilt vinyl window. The broken one measures 3-1/4" total length, the broken end is 3/8" long, and the 2 screw holes are at 1-5/8" and 3".

I need 4 of these

I am looking for replacement pivot pins for the Owens Corning DH or SH. Is this anything you have access to?

attached is a picture of a pivot bar I need to replace. I'm thinking you're 26 - 366 is the closest I'm going to get . I can always drill new holes to accommodate. What do you think? Thanks for your help.

I am looking for a replacement for the pivot bar in the attached photo.

Vinyl window ( no tag or name on the window, can't find the manufacturer, ) i am trying to get the parts , please see pictures, broken round pin , i need to replace full assembly all marked in the pictures Please advise Thank you

One of my pivot bars broke and I am looking for a replacement. The only marking I see is the #3 stamped on it. It looks to be about 3" long and 1/2" wide. I have no idea who the manufacture of the windows are. They are single hung. I was looking at your VINYL WINDOW SASH PIVOT BAR Product Code: 26-3 ... (cont.)

27 1/4 inch tube inside a 12 1/2 spring , with cord to hold up window

Looking for a replacement pivot pin for our window.

Hello, I need some help repairing my window. I think I've narrowed them down to MW manufacturing out of Virginia. I saw the video about upgrading to what looks like the type of hardware I already have. Series 795? I have several broken pieces on both sides so maybe just 2 complete assembly would be ... (cont.)

Ref order #1594931 I have MW single sash vinyl windows, determined I needed S795-29 channel balance and 26-366 pivot bars. All measurements matched up to the old pivot bars in diameter and screw locations, even the lip stop looked the same. The problem came when installing the pin length is shorter ... (cont.)