Viewing all customer Discussions for:

S385-30 30" Series 385 Channel Balance

Vinyl Milgard style windows 32x32 & 32x46 in sashes. Double pane window weights are 26.8 to 27.2 lbs. Balance dimensions are 30" length metal by 1/2 by 1/2 width and depth. Old markings (2) are 29 5 KS CALDWELL, (3) are 29 5 FT CMC 2, (2) are 29 5 HU CMC 5 and (2) are 29 5 GN5 (or 6N5) CMC 45. Top c ... (cont.)

double non swing window i cannot identity a replacement. It is 30 in long. No number on anything to identify1/2 inch wide 30 inch long

hello, First of all let me say that you have one of the most helpful websites that I've encountered in the entire field of home repair. Thanks for that. I need to replace the channel balance on a 33" wide sash window. The only markings on the balance are in the attached photo: 29 3 LS CALDWELL. ... (cont.)

Hi, I am inquiring about replacing old BSI channel balances for non-tilting single sash windows. The 30" S385 series channels look to be correct dimensions. My question is regarding the weight ratings. If my sash's weight comes in at 22.7lbs, should I go for 2930 or 2940, since the weight is r ... (cont.)

I'm looking for Windows Block and Tackle with shoe set. On it it has the following marking - 29-5 KX CMC 7 My guess 29-5 translates to 2950 on your website and I'm thinking the following item is correct replacement - 30" SERIES 385 CHANNEL BALANCE Product Code: S385-30 Appreciate if you can con ... (cont.)

Need to find the replacement parts for this item. Also need the top and bottom clips.

Need to order 2 of these channel balances. Thanks, Ron

I'm looking for replacements for 5 windows with this balance. The only markings I can find on them is the 29 3 B.S.I OL. Can you tell me what part I need?

I need to replace these balance rods:6 rods 2620 27 inches, 2 rods 2330 24 inches,2 rods 2940 30 inches . I also need ten each of the shoes and tops photographed here.

On half inch wide Measures 31 inches from the top of the plastics tip to the bottom of the plastic tip. Which balance do I need?

I will need 4 of this balances Thanks

I measured from steel end to steel end 30 inches. The plastic hardware is the same as the 29" series 385 channel balance. The number stamped into the bar reads 29 9 BSI RK. I would like to order this part from you. My name is Shon Murray. Thank you!

Hello my name is Jorge Blanco (954) 661-6214. I have eleven ES brand Double Hung Impact Windows (heavy). They never worked correctly and the all the balances have started to fail. Some have the DS markings stamped on the balance and others don't ? I have been told that some of these balances may not ... (cont.)

Hello. I need two balance springs for a Lawson window. The sash dimensions are 51? wide x 31? tall and weighs 56 lbs. Thanks, Norm

Series 385 comes fully assembled with the 19-005 top and 15-004 (1-3/32" deep) bottom fittings attached.See 62-005 for the rivet only for replacing a top fitting.

29 4 CX CMC 11 Metal Channel is 30" Windows were installed 16 years ago. The GC was Ryland Homes. Sub Division is Bartram Springs Jacksonville, FL I have 20 windows, probably will order 40 balances if not too expensive.

I have determined that the Series 385 Channel Balance is the correct channel for my Nu Aire windows. I want to verify that the 29-6 AA CMC 11 is the 2960 and the 29-3 CA2 CMC 7 is the 2930 channels. Thank You Richard

I Purchased some channel balances from you recently. They seem to be identical to what I had in my windows. After trying to install the window it appears that the window is not catching the new balance at the bottom. The window has a gap as youWe'll see in the last couple pictures that I sent. If yo ... (cont.)

Hi, most of my windows open. Some are easier than others and some have broken balances. The ones that are difficult to open and or close is it a balance issue. The windows are about 17 years old.

Hi there, I'm hoping you can help me with the replacement part for my window. Please see attached pictures of the parts. The part only lists 2930P, is about 31 inches in length, and half an inch in width. I also added a picture of a window with the piece that is still working and I added another pi ... (cont.)