Viewing all customer Discussions for:

26-119 Sash Release Lever

Here are some pictures of the replacement tilt latch plungers for my double hung windows. Measures 2" long x 3/4" wide. On the picture you will not see the tooth because they are broken off.

Our parts resemble 26-119 in dimensions. Except our bottom tang is not centered but offset by a bit. And there is a small tab on either end of the bottom side of the sash release lever. Is 26-119 a suitable replacement for our application? Thanks for you time

Looking for replacement parts similar or identical to these, top sliding portion says reynolds on the side, r3 10565 is stamped on the internal corner piece

I have several windows having broken latches to release the windows for cleaning. Where can I find the same kind or can be used to replace the broken ones?

I?m looking to replace the tilt out latch for my windows. The brand is Winstrom.

I have visited every department and builder surplus store and cannot find matching internal tilt latch replacements for these windows. I am trying to avoid buying brand new replacement windows because they only need the latches. I also cannot find a manufacturer label or serial number. Please let me ... (cont.)

Can you Please tell me what is the product number on your website for these two parts. I wanna purchase them on your website im just not sure wich ones are they. Thanks

I need to replace several of these tilt in latches on my windows, The latch measures 2" long by 1/2 inch wide. The 2 pieces that break off on the underside are about 1/4 inch between the 2 plastic pieces that fit into the window sill.I believe these windows are Certainteed windows from the late 80 ... (cont.)

Part is 2" long and has grooves to slide to the left to tile window. Mfg by Barrier Ent . Thank you for your assistance

Hey gang, Looking for this tilt latch button. Thanks, Erik

Approx 2" length, 7/8" wideI need at least 6 pieces ASAP!

I am trying to find a replacement vinyl window part, a thumb button for tilt in vinyl window. The windows are Polytex 3500 series. The part (see photos) size is 2 inches by 3/4 inch, and the broken clip part on the bottom of the part is 1/2 inch wide; I'm not sure of the length of the broken off arm ... (cont.)

JELD WEN DROP DOWN WINDOW (TILT DOWN) IT IS WHITE PLASTIC 1and 7/8 inches long by 7/8 inches wide. it has two prongs on the bottom that into top slot of window. there is one clip on each side that you press in at the same time to release window to tilt out. windows are jeld wen 1995 year. ... (cont.)

These are circa 1997 Mastic Inner-lok Vinyla Replacement windows. None of the parts you show match up exactly, but do you have parts that will work? I see some sash release levers that are close. Not sure about the pivot shoe, or if I have even identified that properly. Thanks so much ... (cont.)

Hi do you have this tilt latch in 1 1/2 w X 5/8 L Product Code 26-317

looking for the part that releases the window so it can be dropped in to clean. They are on the top of the window and have prongs that go into the window casing, but the prongs are broken off. The number on the window is 12 10 92 88 I am told they are Vetter windows.

Need to replace left and right

I'm currently looking for a replacement to the Ashland Thumb button 11413. It looks very close to your 26-119. Do you know if this is a drop in replacement? Thanks, Mike

Need a Mastic top tilt corner latch part #4,578,903 R11229 will need 7 LH 8 RH and Sash release lever if your 26-119 will not work with the new ones The bottom ridge prevents it from sliding into the opening. Thanks

I cannot find any numbers or window manufacturer for my windows the release tab in the picture has one side broken. Any help would be appreciated. Thank you Roy