Viewing all customer Discussions for:

39-027E Ellipse Style Single Arm Operator, 9-1/2"

Looking for a single arm operator - see image

Good Afternoon,I am hoping to identify replacement parts for both my Left and right windows. The photos are from the right window. I would need replacements for the arms (left and right), arm cranks (left and right) as well as casement tracks. Can you please provide the replacement part #s for these ... (cont.)

Can you identify a replacement for this window operator?

Hello, I was wondering if you could identify which an operator , this window is Weathershield 1970s to 80s. I was looking at the Ellipse Style Single Arm Operator, 9-1/2" Or 9-1/2" Single Arm Operator, SS Roller

I was wondering if you could tell me what type of arm assembly I have. I think it's a dual arm, but it doesn't match any of the products I've seen. The arms actually work fine. I just need to replace the operator. Can you suggest any replacements?

Hi everyone, can you please tell me which one will match this. Thank you very much!

The window was originally purchased in 1987. The brand was Crestline. Markings on the piece that are barely visible are what appears to be a house and the word TRUTH. The arm is 9 1/2 inches long, measured from the pin on the left end to the center of the pivot in the center of the geared portion ... (cont.)

Hello, I am looking to replace this item. The lenght of the arm appears to be about eight inches. Thanks. Also, I already found the hinge sets I need. They are in my cart.

I am looking for an operator and upper/lower hinges for this window. The operator arm is 9 1/2" from roller to bend before crank. The upper and lower hinges have 10" mounting plates with a 5" swing arm. The hinges are stamped with 385-1 R or 1 L according to location at the top or bottom. I believe ... (cont.)

Hello, I'm looking for some replacement parts for my windows. Thank you for your help.Anthony

Need a new operator. The brand is "Truth". This old one is broken in 2.

I need a replacement for this Truth Wright right hand crank

Hello, I need assistance with identifying and ordering the following parts: -Window crank (the only visible markings are "45054" on the underside). The crank has 12 teeth / splines. -The arm that moves when you turn the crank. The plastic roller on the end (which usually stays inside the housing a ... (cont.)

Am I correct to presume that your part# 39-365 is the direct replacement for my operator shown in the picture? The arm on my operator is 9 1/2" and the screw placement is the same as part# 39-365. Also, I need 10" hinges for these HURD windows. Would I be buying your part# 36-048?Thanks,John ... (cont.)

Arm length is approximately 8 and a 1/2 inches long. Handle section is 4 inches. Wide color is white window swings out to the right period please give pricing on left hand and right hand operator thank you

I need to replace the operator of a nominal 24x40 Hurd casement window purchased in 1988. The existing (bent beyond repair) operator is marked "Wright" and 07702-00. Where can I find a suitable replacement?

Need screws for the parts below. product code -38-075 Product code 39-027E Product code 38-089 Product code 39-533

Looking for replacement of window crank assembly # 30350 on guide arm # 40055 lh. On back of assembly Looking for replacement for left and right hand assemblies Thank you Any additional info needed please let me know

Hello,From checking your site I believe the sash locks replacement would be 38-097 LH and 38-098 RH with new keepers 38-079.However, for the window operators (which I confirm is 9-1/2") seem like 39-027E and 39-028E just not 100% due to the fact the cut sheet on the Ellipse does not show the width o ... (cont.)

I need to replace 2 Truth Window (Right and Left) Casement Operator Single Arm (Right and Left) in Bronze - Including the Handles.