Viewing all customer Discussions for:

39-545 Truth Snap-Stud Bracket

I would love help in identifying the window operator that I've included in photos. Images show measurements of arms and pieces with markings. The house was built and windows installed in 2000/2001. I will need 6 in total: 3 right-hand, 3 left-hand. Thanks, Kristy

Good Afternoon: I have a Truth operator 41011. Works fine except the small metal band that press fits onto the link arm broke. This is the attachment point where I pop the link arm on and off....with the broken ring no longer present, the link arm does not "pop" on and off. I beleive this metal ... (cont.)

This is a Truth 45251 I need to replace, plus the piece that screws into the window, its all one piece. Window was from 2003 with Truth parts Other numbers on arm are 31850... Number on the back of the crank mechanism is 05282003 0233

I have two vertical casement windows measuring 70-3/4" high x 26-1-2" wide.They flank an atrium door. One opens to the right, the other to the left. The operator handle has never been strong enough to open or close these windows without giving them a push, both from inside and out. The handles now d ... (cont.)

I'm looking for a replacement for this Milgard Window crank. Any idea what the part number is? Or where I can get one? Thanks

I need to replace a dual arm casement operator. It is from a Revere window and has the number 1491-220B. The arms are numbered R S-1491-265 and 260.

Need replacement, part number stamped on back is 31876 on arm and 012700 on body.

31850 truth 45251 truth

We currently have a Wright casement operator that we are looking to replace. On the arm it has the following number 07907. On the bottom of the casement operator there appears to be a number # 7107. I think. You can see by the photo that the number is partially missing because of the hole. ... (cont.)

could you assist me in identifying this part as I need to replace it.

Trying to replace these two truth operators, can you help?

have a casement window thats 2 ft wide and can't tell who the manufacturer is. the operator is a Truth brand, arm attach point on the sash appears to be permanently pinned with no stainless spring clip to keep attached? will need that part as well if replacing operator? thanks, Mike ... (cont.)

Hello I need to buy this products . Left hand side and right hand side if you have them . Thank you .Thanh

I need these parts both right and left

Need replacement for this Truth 40056 operator please. Had to tear it out to even determine brand, model etc. so no installed photos but all parts shown.

Afternoon, I'm not sure what it's called, lol but I ordered a replacement arm for my parents crank out window. Little did I know dad replaced it years back and its not the original crank out arm. He had to take off the plate that is attached to the window. In the pics above u can see where the wind ... (cont.)

Hi Dave, I placed an order back on July 19th. Included in this order were two Sash Dyad Crank, 5" 39-187 and 39-188. I finally was able to get my contractor here to install the new window hardware. We discovered that the cranks were not the correct ones. I need Truth (manufacturer) number 45345. Ca ... (cont.)

We had previously purchased a 39-270 closer for a replacement. You show this closer as discontinued. Do you have another solution to replace this closer so the window can operate. Appreciate any help.

Casement window mfg is Silver Line. 17 yrs old. The hole in window (picture 4)is 3 5/8" wide. The arm when straight out is 8 1/2" from base to mounting hole. The long arm is 5" from joint to hole. The short arm is approx. 3 5/8" from base to joint. I tried Swisco part number 39-171, Truth Hardware ... (cont.)

I need to find the part number for this operator for PGT casement Windows WINDGUARD. I need both right and left operators. Thanks