Viewing all customer Discussions for:

82-259 SS Multi-Point Mortise Latch and Keeper

Looking for a replacement lock for a rear slider. It appears to be the SS Multi-Point Mortise Latch and Keeper, Product code 82-259.Or I guess the non-stainless steel version would be the MULTI-POINT MORTISE LOCK AND KEEPER, 9-7/8"Product Code: 82-239

Pat # 6.264.252. And pat #5.820.170 Looking for this lock please help

Hello, I need to replace a double latch mortise lock on my sliding glass door. I have identified your multi-point mortise latch 82-259 as the most likely replacement part. However, I am concerned the 3/4" width is far wider than my approximately 1/2" opening for the replacement part. Please see atta ... (cont.)

I need to replace the locking handles on my slider door and want to use the existing mortise which has a double hook, will this one work ? The screw holes are 3 15/16 apart on existing handle and the mortise looks similar to your 82-259. The door is 2 inches wide. Thanks !

What about the mortise? I run a hotel in Florida, and I need help with my mortise. I'm attaching photos of my part. The blue line in photo 4 is about 6-3/8".

Hi, Will the 82-249 keeper work with a 82-259 mortise lock?

I need help in determining what I need to replace a broken lock.

Do you guys have by any chance this same lock and keeper made of stainless steel?

No names, numbers, or markings on hardware. Holes 4 inch centers Door 1 1/2 inch thick Resembles American Signature Series 50 from Home Depot but not a match. Installed 5 plus years ago. Want as shown - keyed lock.

Hello I am looking to purchase a patio sliding door lock full set ( handles and keys) I have patent No. 6.245.252. 5820.170 I attached a picture of my old lock. I need to replace it

I am looking for the attached door lock.. please let me know what the part number is so we can order this. Thank youBob

Hi I found part #82-239 and 82-259 somewhat similar to the one that is missing from my other existing door. Can you tell me which one I should get and please include the handle too because it's missing the lever latch. The hole spacing of the door handle is 3-15/16" and the thickness is about 1-5/ ... (cont.)

VANGUARD PAT # US 6672632

I purchased and returned mortise lock 82-259. It is not exactly a replacement for our original lock. Can you suggest a better replacement. I have attached photos of the new and old lock.

My sliding door is not fitted with a keeper and I have the a multi point latch lock without a slam button. The lock is 11" on center between the screw holes (i think similar to 82-259). I have a spare latch that does come with a slam button and unfortunately I can't get the door to latch even with l ... (cont.)

Hello. I need help identifying the part shown in the provided photos. It's a double hook mortise lock and the only marking on it is the phrase "Pat. Pend." It measures approximately 9.8 inches in length and 0.75 inches in width. Other than that, I'm at a loss as to who makes it or if there is a repl ... (cont.)

This is from a JW patio door. If you look at pic it has PAT# 6.264.252 & 5.820.170 it's on the side I measured from top to bottom cover it's 11 1/2 and from screw to screw 11 inches.

My part looks just like your 82-259, almost same dimensions. I need only the keeper for this unit. Some person installed the partial lock on my 93 old mother's door. I just now noticed that the keeper was not installed and there is no key to this lock.I found the lever and the lock pieces. Now pl ... (cont.)

We purchased the 82-259 lock and it fit perfectly where the broken lock was but now when in the locked position the door can be pulled apart. It looks like the latches aren't locking onto the strike plate or keeper, not sure what is the correct term. We can slide the plate that we have up and down ... (cont.)

The handle that activates the lock to lock and unlock broke and I need to find a replacement handle that will work with this lock. Thank you