Viewing all customer Discussions for:

39-412 Offset Single Arm Operator, 9-1/2

The operator is loose and has a lot of play in it when the window is open. Would like to replace.

Hello,I purchased items 39-412 & 39-413 for my window. The window channel that is on the window is too shallow for these parts. The current channel measure 13 3/4 x 5/8 x 1/8. It seams that we need new ones that are 13 3/4 x 5/8 x 1/4 Would this be the part that I would need to order? SS 13-3/4" ... (cont.)

Need a replacement right handed operator, 9" arm. Photos of similar window operator attached. Another similar operator has a tag JEL-N-555, but this is a different window (same window type and build) in the house. I actually only need the roller on the end of the arm, if that's repalceable. The ... (cont.)

what is the width of crank housing/

The 39-412 is almost perfect--the only difference I can see vs. an Andersen 2420 LH is the direction of the offset bend. The 2420 bend down, your 39-412 bends up. Is the arm of the 39-412 user-swappable? I.e.: might I be able to change a RH arm into this unit upside down? This would also need the ... (cont.)

I have a Silverline Casement window which has a rusted and broken operator swing arm on the lower sill. I contacted Silverline and they said the part is not made anymore and provided Swisco as a contact to look for a substitute piece. I?m hoping you have a part that will work and advice on how to in ... (cont.)

I have few windows with the arm showing in the pictures below. I rarely open my windows because the plastic wheel on the arm keeps coming off from the rail attached to the window. I already had an incident (the wind blew the window wide open and broke it on the impact). I replaced one of the arm b ... (cont.)

Says truth on the arm on one side. Has the number 30049 on the other.

Thanks for writing in. To start, review our 39-413 & 39-412 operators. Like your old operator, they have an offset in the link arm that goes up. The arms are 9-1/2" long. Go over all the specifications listed and see if you think these are what you're looking for. They are compatible with the 39 ... (cont.)

Looking for pictured window crank

Truth stamped on it

Hi,The circular piece that runs along the corridor on the bottom of the window is frayed and worn. The window will not open and shut like it should, and I believe this is the culprit. I think that I will need to replace this part. Can you help me? My window has the NORCO WINDOWS model description #: ... (cont.)

Can you advise what I need?

I am looking for replacement for Truth 45034LH... (3x) part 39028(left side crank) looks like exact replacement, is it available? I also looked at Ellipse 39-027E which has same measurements... Then saw Offset39-412, which also has correct measurements. Which is right for me? Wha ... (cont.)

Hello, I'm looking for replacements for some old window operators. The first is an awning window with a 27" track. The glass size is 35-3/4" x 13-1/2". The arm is between 10-1/2" and 11" from the end to the elbow. Pictures 1-3. The second is a casement window with a 14-1/2" track. The glass si ... (cont.)

I saw other questions about this single arm crank operator but but mine isnt 13 1/2 iches long? Truth is inprinted on the arm crank

Hey, I am looking for casement operators for Norco D-series windows. The number stamped on the hardware is 076-N-330. They use the typical single arm truth hardware. The single arm is about 8-9" long (didn't really know where to measure it from.)

I have a 9 1/2 single arm casement window with a screw in the left side. How do I get the cover off after removing the screw and loosing the paint? The house was built in 1953. Thank you!

I have a Norco casement window with a broken Truth operator. I identified the operator as a right hand 15.08 - with a 9 1/2" offset arm. I work in the industry so I am familiar with the hardware. I did not see it on the current Truth web site, so it may have been discontinued or replaced with a diff ... (cont.)